Responsibility book for electrical safety production

Letter of Responsibility for Electrical Safety Work (5 selected articles)

In life, we often come into contact with the responsibility book, which helps to enhance our awareness of market competition, responsibility and safety. Do you know the format of the responsibility book? The following is my carefully compiled responsibility book for electrical safety production (5 selected articles), for reference only, and you are welcome to read it.

Electrical Safety Production Responsibility Letter 1 In order to better implement the enterprise's safety policy of "safety first, prevention first", strengthen the safety management of projects under construction, improve the safety awareness of all employees, and build projects that are satisfactory to the owners. Ensure the realization of the overall goal of the headquarters' 20xx safety work, and put an end to the death and serious injury accidents caused by the responsibility in the project. The Safety Assurance Responsibility Certificate is specially formulated. Combining responsibility with rights, paying equal attention to rewards and punishment, and combining with the actual project of this bid section, the post safety responsibility and reward and punishment standards are determined as follows:

A, job responsibilities:

Responsible for the electrician work in the headquarters.

Second, the responsibility requirements:

1, part-time electrician, not allowed to operate electrical equipment. Electricians must hold a qualified and effective operation certificate and pass the examination before they can work at their posts.

2. Indoor lighting circuits shall be fixed with porcelain clips.

3. Non-electricians are forbidden to remove electrical equipment.

4, all kinds of wires, wiring, should use the corresponding voltage level between insulated wires and porcelain clips, porcelain tubes, porcelain bottles.

5, wire connector should be strong, and the application of insulating tape bandage, can't drag on the ground, must use wooden hanging.

6, fuse should be installed according to the electricity load.

7. The location, spacing and height of the wires erected on site must meet the requirements of the power sector.

8. Transformers and power distribution equipment on the construction site should have perfect shielding protection devices, and transformers installed outdoors and indoor transformers and power distribution equipment should have shielding and fences. And should be equipped with obvious warning signs.

9. On-site electrical wiring installation should be carried out in accordance with standards. It is forbidden to tie the line to wooden stakes, trees and iron frames without porcelain clips.

10, all outdoor breaker should be located in the iron table board box, and set up a canopy, leakage protector must be installed and locked.

1 1, the wires and cables pulled at the construction site must be hung at a certain height according to regulations, and it is forbidden to put them on the ground.

12, the metal shell of electrical equipment and the supporting switchboard should have reliable grounding devices. The fuse switch in the circuit must comply with the provisions of the electricity standard, and the switch directly operated by hand must have a complete insulating shell.

Third, the reward and punishment standard:

1, reward indicator:

Outstanding achievements, safety and no accidents within the scope of duties throughout the year, a one-time reward of XXX yuan.

2, the punishment index:

The responsible object causing safety accidents shall be dealt with according to the reward and punishment system for safety production of the headquarters after being audited by the leading group for safety production of the headquarters.

XXX

XXXX，XXXX，XX，XX

Electrical Safety Production Responsibility Letter 2 In order to conscientiously implement the spirit of relevant documents of provinces, cities and counties on strengthening the safety production management of mining enterprises, combined with the actual situation of our mine, the 20xx annual safety production responsibility letter was signed for safety production management personnel and special type of work operators. The purpose of signing the responsibility book for safety production is to further clarify their respective responsibilities and ensure the safety production in 20xx years. Job safety responsibilities are as follows:

1, in strict accordance with the requirements of the "Regulations", responsible for the daily maintenance of underground electrical appliances, timely handling of underground mechanical and electrical failures, and ensuring the normal operation of production.

2, actively participate in all kinds of safety technical training, and constantly improve their technical ability, the underground power supply system and equipment to achieve "three understanding, four will" (understand the performance, understand the structure and safety devices; Can operate, maintain, maintain and troubleshoot).

3. Stick to the post, strictly implement the succession system, strictly implement the power-off and power-on system stipulated in the "Regulations", and make a record of power-off and power-on of the main fan. After checking the normal operation of the main fan, report to the mine manager on duty to ensure that the underground power supply system and electrical equipment are in good condition at all times.

4, underground maintenance of electrical equipment, it is forbidden to live work.

5, strengthen the patrol inspection of underground electrical appliances and power supply system, eliminate hidden dangers in time, and deal with problems quickly, accurately and standardized. If you find any problem that cannot be solved, you should report it to the monitor on duty and the safety officer in time.

6, fill in all kinds of drawings, cards, tables, boards, and make relevant records.

Matters not covered in this responsibility book shall be implemented according to "Coal Mine Safety Regulations".

Person in charge: xxx

Legal representative: xxx

XXXX，XXXX，XX，XX

Electrical Safety Work Responsibility Letter 3 Party A: _ _ _ _ _ _ (hereinafter referred to as Party A)

Party B: _ _ _ _ _ _ _ (hereinafter referred to as Party B)

According to the requirements of relevant national safety laws and regulations, combined with the actual situation of our company, we will conscientiously implement the "6 1" instruction, implement the policy of "safety first, prevention first" and the principles of "who is in charge, who is responsible" and "safety must be paid attention to in production", and implement the safety responsibility system. In order to ensure construction safety and prevent accidents, Party A and Party B must perform the following clauses:

1. Party A shall fully cooperate with the security work of this project, supervise and inspect the security work of Party B at the same time, and have the right to require Party B to rectify the violations, illegal acts and potential safety hazards found in the inspection.

2. Party A shall, according to the requirements of the company, notify Party B of the problems found in the inspection in writing and file them for future reference.

3. Party A has the right to punish Party B's "three violations" according to relevant management measures.

4. Party A shall report the safety management of the decoration project to the company in time.

5. Party B must have a clear legal person in charge of safety, who is responsible for the safety and public order of the construction project, so as to achieve "five simultaneities" of construction and safety.

6. Before entering the construction site, Party B must register and pass for the construction personnel, and designate a special person to do the inspection. Unlicensed persons are not allowed to enter the construction site.

7. Before Party B takes up his post, he must be responsible for the safety education of construction personnel, make clear the relevant safety regulations and work requirements, and consciously abide by the safety management system.

8. Party B must be equipped with full-time or part-time security personnel during the construction period, specifically responsible for the implementation of safety and public security precautions during the construction period.

9. The inflammable, explosive and dangerous goods used by Party B in the construction must be restricted, and a special person shall be appointed to take charge of safety management.

10. When Party B uses fire, electricity and welding in the construction, it must be approved by the person in charge of Party B's site, and strictly implement the technical specifications and operating procedures of fire, electricity and welding to ensure foolproof. (Oxygen cylinders and acetylene cylinders shall not be inverted, with damping rings, and their number shall be strictly controlled. The spacing is greater than 5m, and the distance between the open flame and the acetylene bottle must be greater than 10m. There is a special person to eliminate flammable materials, put a fire extinguisher on site, leave a special person on duty after welding, and leave after confirming that there is no problem.

1 1. Party B's electricians and electric (gas) welders must hold a valid Operation Certificate for Special Industry Personnel issued by the labor department before they can operate according to the requirements of construction site specifications.

12. Party B must carry out the construction in strict accordance with the national safety construction standards for building decoration industry and resolutely put an end to "three violations".

13. When Party B uses large-scale equipment in construction, it must fully consider the bearing capacity and seismic capacity of the floor, and can only use it on the premise of ensuring safety. It is strictly forbidden to command and take risks in violation of regulations.

14. Party B must erect safety protection X for dangerous openings (access openings, elevator openings, reserved openings, stairs, etc.). ) During construction, the safety rope for aerial work must be fastened.

15. Smoking, using naked flames, leaving behind construction workers and using electric water heaters are strictly prohibited in the decoration area.

16, it is forbidden to pile up a large amount of waste for a long time in the construction area, block the evacuation passage, and insist on cleaning it up once a day, especially the empty bottles such as glass glue and paint should be properly handled.

17. Party B must strictly manage the construction site, and the equipment, equipment, tools and materials on the construction site must be managed by special personnel.

18. Party B must equip the construction site with fire-fighting equipment that meets the specifications and standards to ensure the safety of the whole construction process.

19. If Party B neglects safety management or violates the provisions of the contract, resulting in accidents and cases, Party B shall bear all the responsibilities, and all the economic losses and political impacts brought to Party A therefrom shall be borne by Party B. ..

20. This responsibility shall come into effect as of the date of signing, and shall become invalid after the project is accepted, in duplicate, one for the owner and one for the construction unit.

Party A: _ _ _ _ _ _ _

Party B: _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Electrical safety production responsibility book 4 According to the Safety Production Law of People's Republic of China (PRC), in order to ensure the implementation of the company's safety production work, the responsibility system for safety production is formulated, and the safety production responsibilities of this position are defined as follows:

A, all electrical wiring, power supply and distribution equipment, must be reasonable design, correct installation, according to the provisions of the use.

Second, the installation and maintenance of electrical equipment and the connection and disconnection of wires must be carried out by full-time electricians, and no one may operate them without permission.

Three, to contact the use of electrical equipment workers, to strengthen the safety of electricity knowledge education, to avoid electric shock and fire accidents caused by improper use.

Four, the electrical equipment, should strengthen the inspection and maintenance, to prevent their own fire and explosion.

Five, to check regularly, replace the electrical circuit, to prevent the circuit corrosion and aging caused by leakage short circuit.

Six, flammable and explosive places should be in accordance with the provisions, choose explosion-proof electrical appliances, switches and lamps and lanterns, line requirements laid in protective casing.

Seven, temporary electricity should be approved by the security department, and in accordance with the provisions of the temporary electricity license before.

Eight, according to the provisions set lightning protection device and electrostatic grounding device, and regular inspection, make it meet the safety requirements.

Nine, the power supply and distribution room should be tight, prevent outsiders from entering, prevent small animals from entering and causing short circuit, and prevent rain leakage.

Ten, electrical fire, should first cut off the power supply, and then put out the fire. Foam extinguisher is strictly prohibited when fighting. Dry powder fire extinguisher and carbon dioxide fire extinguisher can be used.

Eleven, all electrical maintenance, must be a power outage, and hung on the power switch handle "someone work, no closing" sign. Under normal circumstances, live working is prohibited. If live maintenance is needed, it should be approved by the leader and reliable safety measures should be taken. Maintenance personnel and guardians must be electricians with practical experience. Otherwise, work is not allowed.

Twelve, electrical workers, should wear labor protection articles in accordance with the provisions, the correct use of electrical tools and fire equipment that meet the safety requirements.

Thirteen, electrical operators should strictly implement the operation ticket, working ticket system, work permit system and work supervision system.

Fourteen, often patrol the running electrical equipment, monitoring the operation of the equipment; Timely rectification or report hidden dangers.

Fifteen, when using hand-held lights and entering a confined space, low-voltage electricity (36 volts) must be used according to regulations, and it must be used under special circumstances.

12 volt low voltage.

Sixteen, replace the fuse, should be strictly in accordance with the provisions, choose the fuse, not to use other metal wires.

This responsibility shall come into effect after being signed. The person in charge of production safety has understood the above requirements of production safety responsibility and promised to be responsible for the safety accidents in the management area. If there is a safety accident due to poor operation, he is willing to bear the corresponding legal responsibility.

1. For those who neglect their duties and are irresponsible in their work, the company will deal with them seriously according to the seriousness of the case until they are investigated for criminal responsibility.

2. If the major safety hazards existing in this area cannot be rectified in time or major safety accidents are caused by poor work, the relevant responsible personnel shall be given administrative sanctions in accordance with the Provisions of the State Council on the Investigation of Administrative Responsibility for Extraordinary Safety Accidents; If a crime is constituted, criminal responsibility shall be investigated according to law.

xxx

Xx，xx，XX，XX

Electrical Safety Production Responsibility Letter 5 is to implement the Safety Production Law and the policy of "Safety First, Prevention First", strengthen the safety responsibility consciousness of all units and employees of the company, firmly establish the safety responsibility consciousness, eliminate all kinds of unsafe hidden dangers to the maximum extent, and nip all accidents and signs in the bud. In order to implement the responsibilities layer by layer, prevent accidents, resolutely curb the occurrence of serious accidents, realize "safe production and long-term alarm", and ensure the smooth progress of all the work of the company. To this end, the company's safety production leading group signed the following safety responsibility letter with the company's subordinate units:

A, put an end to the responsibility of employee casualties.

(a) it is strictly prohibited to have work-related deaths and serious disability accidents (including work-related injuries with reimbursement amount exceeding 5,000 yuan);

(2) No more than 1 employees (including those who need to stop work and rest due to work-related injuries identified by the hospital) have work-related accidents (the reimbursement amount is within 5,000 yuan in 200 yuan), and the number of minor injuries (the reimbursement amount is within 200 yuan) is within 3 times; Do not exceed 1 security incidents (theft of companies and individuals, and other disputes);

Second, to prevent fire accident responsibility target

(1) No fire accident with direct economic loss of more than 65,438+0,000 yuan occurred in all units of the company;

(2) The fire symptoms of each unit shall not exceed 1/ year (put out quickly after the fire, no casualties, no direct losses).

(three) put an end to serious injuries and casualties, and put an end to major fire, burning and explosion accidents.

Third, the electrician's safety responsibility

(a) to learn and be familiar with the operating rules of safety technology, abide by the laws and regulations of the state, and implement the specifications and technical requirements of the superior power consumption.

(2) Take an active part in all kinds of safety production activities, receive all kinds of safety education, abide by rules and regulations and disciplines, do not violate labor discipline, stick to their posts, do not leave their posts, do not work after drinking, and concentrate on their work.

(3) Seriously study the operating rules of electrical safety technology, so as to know fairly well. Familiar with safety knowledge, operate according to the rules, do not operate illegally, do not take risks recklessly, and have the right to refuse illegal orders.

(four) adhere to the daily inspection system. Leakage trippers and electrical equipment, especially mobile and hand-held power tools, lighting lamps and mopping cables, should be inspected regularly to eliminate unsafe factors, and can only be delivered after acceptance meets safety requirements, and electrical equipment should be maintained regularly.

(5) Improve and enhance their own technical and professional level, be responsible for their own work, be not careless or casual, regularly check the construction electricity consumption, improve and rectify in time, correctly use electrical labor protection articles, wear neat clothes, insulated shoes, safety helmets and take up their posts. They should fasten their seat belts when working at high altitude or in dangerous places.

(6) It is strictly forbidden to work with electricity or take risks. If hidden dangers are found, they should be rectified immediately. Never find hidden dangers, rectify and report them. The hidden dangers raised in the exam will be rectified in time as required.

(seven) the implementation of civilized construction, do not throw things from a height, the use of wires in a timely manner to recover, properly keep, line erection norms, distribution box, switch box locked in time, electricity signs are obvious.

(8) Operating procedures must be strictly implemented in case of power failure. There must be a special person in charge of power failure and transmission. The power failure switch should be locked, and warning signs such as "Someone is working" and "No power transmission" should be hung on the switch. Live working is strictly prohibited.

(9) In case of power failure in the factory, it is necessary to do a good job in preventing safety accidents such as power exchange during power generation to prevent safety accidents.

Fourth, the company rewards and punishments for the safety assessment of each unit.

(1) The company's production safety leading group shall summarize and evaluate the production safety situation of each unit in the previous year according to the usual or monthly production safety inspection and accident records before 65438+10.20 every year, and award the safety award to the unit with good year-end performance and the flowing red flag to the advanced unit with production safety.

(two) more than one major accident occurred in this year, and the person responsible for serious dereliction of duty (causing death, disability, and major economic losses) shall be removed from his post of responsibility according to the seriousness of the case, or the corresponding responsibility shall be investigated:

1. In case of violation of relevant safety management laws and regulations, the responsible person shall be given administrative and economic punishment until criminal responsibility is investigated;

2. The responsibility time of this responsibility letter is from June 65438+1 October1day in XXX to February 3 1 day in XXX.

XXXXX New Energy Automobile Co., Ltd.:

Responsible unit:

Person in charge of safety production management team:

Signature of person in charge:

XXXX，XXXX，XX，XX

;