How to polish sanitary ware?

Look slowly

Family room decoration construction agreement

According to the "Contract Law of the People's Republic of China" and the "Construction and Installation Project Contract Regulations" ", "Consumer Rights and Interests Protection Law of the People's Republic of China", "Price Law of the People's Republic of China", "Shanghai Regulations on the Protection of Legitimate Consumer Rights and Interests", Ministry of Construction of the People's Republic of China (1997 ) No. 92 "Trial Measures for the Management of Family Room Decoration and Renovation" and the principles stipulated in other relevant laws and regulations. In order to protect the legitimate rights and interests of both parties and based on the specific circumstances of this project, Party A and Party B shall act on the basis of equality, friendship, voluntariness and consensus through consultation. On the basis of this, the following agreement has been reached and we agree to abide by it.

Contractor (hereinafter referred to as Party A): (Owner) Contact information:

ID card: Address:

Contractor (hereinafter referred to as Party B): ( Leader of the construction engineering team)

ID card: Contact information:

Home address: Home landline phone number:

Overview of the first project

1. Party A’s decorated house is a legal residence.

2. Decoration construction location:

3. Construction scope: Bedroom, living room, dining room, kitchen, bathroom, balcony, interior area: square meters.

4. Decoration construction content: Water, electricity and weak current renovation project of Party A’s house, wall renovation, production of window and door covers, floor tiles and ceramic tile paving, floor keel, rug floor laying, and suspended ceiling Installation, ceiling and wall coatings, installation of kitchenware, sanitary ware, lamps, doors and other facilities, storage rooms, transportation projects and other other projects agreed by both parties as well as all projects that should be included in the residential interior decoration project (the cost of the drilling project will be borne by Party A Party shall be responsible for this at its own risk).

5. The contracting method is that Party B contracts part of the materials.

6. Total price: ￥ Yuan, capitalized (RMB):

Among them:

Material fee: RMB Yuan. Labor cost: RMB yuan.

Management fee: None. Design fee: None.

Garbage removal fee: None. Taxes: None.

Material handling fee: None.

Other fees: None.

The above total price is determined based on Party B’s on-site inspection of Party A’s house and preliminary understanding of the required work. The total price is a closed price, including all labor and Annex 3 in the decoration project undertaken by Party B. All other auxiliary material costs other than the "List of Materials Purchased by Party A".

If Party A changes the construction content or materials, the additional material costs will be calculated on an actual basis.

7. Construction period: Starting from _year_ _month_ _day to completion on _ _year_month_ _day, the construction period is _ _days.

Article 2 Agreement on the responsibilities of both parties

1. Party A's responsibilities:

(1) Party A shall make an on-site explanation to Party B one day before the start of construction. Provide Party B with necessary conditions such as water and electricity required for construction, and explain the precautions for use.

(2) Coordinate the temporary use of public parts during construction and the impact on neighborhood relations.

(3) If it is really necessary to dismantle or modify the original building structure or design pipelines, you are responsible for going to the local housing management department or property management department to go through the corresponding approval procedures and bear the relevant costs.

(4) Provide self-purchased materials on time according to the needs provided by Party B.

2. Party B's responsibilities:

(1) Participate in the on-site presentation of the construction design plan organized by Party A, and be responsible for communicating Party A's design plan and construction results to specific construction personnel.

(2) Party B shall fully assume the management and construction responsibilities of the person in charge of the construction engineering team during the decoration period, and shall be responsible for the quality, construction period and construction site safety of this decoration project.

Party B is fully responsible for liaison with Party A, ensuring the quality of materials provided, raising material requirements to Party A, and on-site management of decoration construction quality and construction personnel.

(3) The person in charge of Party B is responsible for organizing the decoration personnel to participate in the decoration project defined in this contract, and is responsible for the personal safety of the construction personnel. During the construction of a single project, Party B is not allowed to change construction personnel without Party A's permission; replacement of construction personnel approved by Party A must be done under the premise of ensuring construction quality; if Party A has doubts about the construction level of Party B's decoration personnel, Party B shall replace it unconditionally.

Article 3 Agreement on Material Supply

1. Materials provided by Party A: (See Appendix 3 "List of Materials Purchased by Party A").

Party A is responsible for purchasing and supplying materials and equipment, which should meet the design requirements and be delivered to the site on time. Party A and Party B should handle the handover procedures. If Party B discovers quality problems or specification differences in the materials and equipment provided by Party A, it should promptly report them to Party A. Party A still expresses its intention to use them, and Party A will bear the responsibility for any resulting project losses and delays. After the materials supplied by Party A arrive at the site on time and are accepted by both parties, Party B will be responsible for keeping and organizing the construction. Party B will be responsible for compensation for material losses caused by improper storage or improper construction techniques.

2. The decorative materials and equipment purchased and supplied by Party A shall be used for residential decoration as stipulated in this contract. Party B shall not misappropriate them for other purposes without the consent of Party A. If Party B violates this provision, Party A shall be compensated double the price of the misappropriated materials and equipment.

3． Party B shall provide construction tools and tools; materials provided by Party B: (See Appendix 2 "Contracting Materials Quotation").

Party B shall supply materials and equipment in strict accordance with the brands, specifications, models and other contents and design and construction requirements specified in Appendix 2 "Contracting Materials Quotation"; materials without specified brands shall meet national and industry regulations. Quality and environmental protection standards; Party A shall go to the site for acceptance. If it does not meet the design and construction requirements, quality, environmental protection or specifications are different, use shall be prohibited. If it has been used, Party B will be responsible for any losses caused to the project.

4. All materials contracted by Party B shall be transported to the home by themselves.

For materials purchased by Party A, Party A promises to try its best to ask the decoration material supplier to deliver the decoration materials to Party A's house free of charge. However, if the material supplier insists on delivering the goods only to the downstairs of Party A's residence, Party B will be responsible for transporting the decoration materials into the house.

5. In order to ensure the normal progress of the project, Party B must submit to Party A in writing at least one week in advance a list of materials to be purchased for the next process

so that Party A can purchase them on the weekend. Material. Party A shall provide Party B with the materials required on time. Party B must also provide approximately accurate (/-10) quantities of required materials. The transportation costs for repurchasing materials or returning materials due to Party B's material estimation error being greater than 10% will be borne by Party B, or Party B will be responsible for transporting them back to the supplier.

Article 4 Agreement on Project Quality and Acceptance

1. This project implements DBJ08-62-97 "Technical Regulations for Residential Building Decoration Engineering", DB31/T30-1999 "Acceptance Standards for Residential Decoration and Decoration" and other local standards and quality assessment acceptance standards formulated by the municipal construction administrative department.

2. Party A provides the design and construction plan for this project. Party B is responsible for carrying out construction in accordance with relevant industry regulations and with reference to the construction technology agreed in Appendix 6 "Construction Technology List".

3． Regarding the construction technology, both parties have made the following additional agreements:

1. Bathrooms and kitchens must be waterproofed and undergo a 12-hour water leakage test

2. The sanitary ware is firmly fixed and the pipe connections are tight.

3． The line must be able to twitch after being threaded through the tube.

4． The fir floor is laid at a 45-degree angle to the joist and fixed with wood screws.

5. Wall latex paint, one bottom and two sides

6. Door pockets and skirting lines, one base and three sides

7. Door, one base and three sides

4. If the quality of materials and equipment provided by Party A is unqualified and affects the quality of the project, Party A will bear the rework costs and the construction period will be postponed.

5. If a quality accident is caused by Party B, Party B will be responsible for the rework costs and material losses. If any property damage to surrounding neighbors is caused by construction quality problems during the construction period and warranty period of this construction site, Party B will be responsible for repairs and compensation;

6. During the construction process, if Party A puts forward design modification opinions and adds or deletes engineering items, it must contact Party B in advance before proceeding with the construction of the project.

7. If some processes are installed free of charge by Party A's material supplier or Party A arranges for installation by other units, Party A shall arrange the time in advance and notify Party B. Party B shall cooperate and avoid delays in the overall construction period.

8． Project acceptance: Party A and Party B shall handle the inspection and acceptance procedures for concealed projects and intermediate projects in a timely manner. At each node of the project, Party B shall notify Party A two days in advance for acceptance. Party B shall not proceed with the next phase of project construction without Party A's written confirmation in Appendix 4 "Project Quality Acceptance Form". (Refer to Shanghai local standard DB31/T30-1999 "Residential Decoration Acceptance Standard" and Appendix 6 "Construction Technology List"). If Party A cannot organize acceptance within the specified time, Party B must be notified promptly and another date for acceptance shall be set. If the completion acceptance is passed, Party A shall recognize the original completion date.

9． Completion of the project: Party B shall notify Party A for acceptance two days in advance. Party A shall organize acceptance within three days of receiving the notice and complete the acceptance confirmation procedures in writing (see Appendix 4 "Project Quality Acceptance Form"). If Party A cannot organize acceptance within the specified time, Party B must be notified promptly and another date for acceptance shall be set. If the completion acceptance is passed, Party A shall recognize the original completion date.

10． The project warranty period is one year, starting from the date of completion acceptance confirmation. During the warranty period, if there are quality problems caused by improper construction by Party B and unqualified materials provided by Party B, Party B will unconditionally carry out repairs and bear the corresponding material costs. If any loss is caused to Party A due to the above reasons, Party B shall bear the corresponding liability for compensation; if the damage is caused by improper use by Party A during the warranty period until it cannot be used normally, Party B may charge as appropriate. After the warranty period ends, Party B is responsible for providing long-term maintenance services to Party A until Party A resumes the renovation project of the house.

Article 5 Agreement on production safety and fire prevention

1. The construction requirements provided by Party A should be negotiated with Party B. The construction site should meet the requirements for fire prevention and accident prevention, including that electrical lines, gas pipelines, tap water and other pipelines are smooth and qualified. Party B shall take necessary safety protection and fire-fighting measures during construction to ensure the safety of workers and adjacent residents, comply with the decoration guidelines of the property management department (see Appendix 1), and prevent pipes in adjacent residents’ houses from being blocked, water leakage, Accidents such as power outages and damaged items occur. If the above situation occurs, if it is Party A's responsibility, Party A will be responsible for repairs and compensation; if it is Party B's responsibility, Party B will be responsible for repairs and compensation.

2. If the construction involves changing the structure of the house, demolishing or modifying load-bearing walls, or increasing the load on the floor (ground), Party A will negotiate with the property management department, and construction will be carried out after confirmation.

3． Party B should pay attention to the safety of gas use, ensure the safety of climbing construction and other safety guarantees, and remind construction workers to pay attention to safety. The responsibility for any accidents lies entirely with Party B.

Article 6 Agreement on Project Price and Settlement

1. Project Payment Method:

Project and Material Payment Schedule

Payment time Project payment proportion Amount of material payment Total amount

Within three days after the contract is signed and before the start of construction 30

Within two days if the water and electricity acceptance is qualified 0

30% before the painter enters the site halfway through the construction period

30% on the day of completion acceptance and acceptance

10% six months from the date of acceptance of the final payment of the project warranty

2. Receipts should be issued for all transactions between the two parties.

3． Project Settlement: (See Appendix 5 "Project Settlement Form").

Article 7 Liability for breach of contract

1. If the construction is overdue due to Party A's reasons, Party A will pay Party B 50 yuan in liquidated damages for each overdue day after 15 days of overdue delay. If Party A fails to pay according to the time agreed in the agreement, interest will be paid to Party B on the overdue portion during the overdue period at the current bank deposit interest rate for the same period.

2. If the construction is overdue due to Party B's reasons, Party B shall pay Party A 50 yuan in liquidated damages for each overdue day after 15 days of overdue delay.

3． Party A fails to complete the relevant procedures and forces Party B to dismantle and modify the original building load-bearing structure and service equipment and pipelines. Party A will be responsible and liable for any resulting losses or accidents (including fines).

4． If Party B dismantles or modifies the original building load-bearing structure or service equipment and pipelines without authorization, Party B shall be responsible and liable for any losses or accidents (including fines) caused thereby.

5. If the project has not gone through the acceptance and settlement procedures, and Party A uses the project in advance or uses the project without authorization, Party A will be responsible for the failure of acceptance and losses.

6. If the key nodes of the project are not accepted for acceptance, Party B will proceed with the next phase of project construction in advance. Party B will be responsible for any losses caused thereby.

7. If Party B fails to supply materials and equipment in accordance with the brand, specifications, models and other content and design and construction requirements specified in Appendix 2 "Contracting Materials Quotation", Party B shall compensate Party A double the price of the counterfeit and shoddy materials; if Party A is therefore If any losses are caused, Party B shall bear all liability for compensation.

8． If during the construction process, engineering and material quality problems arise, as well as various responsibilities that should be borne by the construction engineering team, Party A will only hold Party B accountable for compensation.

Article 8 Dispute Resolution Methods

When a dispute arises between the two parties due to project quality, both parties should try their best to negotiate. Or if negotiation fails, you can apply for arbitration to the Shanghai Arbitration Commission or file a lawsuit with the People's Court in accordance with this agreement

Article 9 Modification and termination of the agreement

1． After the agreement is signed by both parties and becomes effective, both parties must strictly abide by it. If any party needs to change the content of the agreement, it should sign a new supplementary clause after reaching consensus through consultation.

2. If any party proposes to terminate the agreement during the construction process, it must submit it in writing to the other party, and both parties must agree to go through the liquidation procedures, enter into a termination agreement, and terminate this agreement.

3． If there are quality problems in Party B's construction, Party A may unconditionally terminate the agreement without Party B's approval.

Article 10 Supplementary Provisions

1. Before the start of the project, Party A shall hand over the key to the exterior door of the house to the person in charge of Party B's construction team for safekeeping. When the project is completed and accepted, Party A is responsible for providing _1_ set of new locks, and Party B is responsible for installing and delivering them for use on the spot.

2. After signing this agreement, the project shall not be subcontracted.

3． This agreement is made in 2 copies, with Party A and Party B each holding one copy. The attachment is an integral part of this agreement and has the same legal effect.

Attachment to Article 11 Agreement

Attachment 1: Decoration Guidelines of the Property Management Department

Attachment 2: Contracting Materials Quotation

Attachment 3: List of materials purchased by Party A

Attachment 4: Project quality acceptance form

Attachment 5: Project settlement form

Attachment 6: Construction process list

Party A (signature): Party B (signature):

Address: Address:

Telephone: Telephone:

Postcode: Postcode:

Date of signing: Year, month and day

Place of signing:

Attachment 2:

Quotation form for contracting materials

Party A:

Party B:

Category Name Brand Specifications Unit Quantity Unit Price Total Price Remarks

Wood Materials Fir Wood Flooring

Wood Materials Larch floor grille

Wood material Pinus sylvestris

Artificial board type gypsum board

Artificial board type Meranti plywood

Artificial board type 12mm high density board

Artificial board type five plywood

Artificial board type block board

Line type solid wood door cover line

Line type solid wood baseboards

White paint furniture topcoat

White paint furniture primer

Paint thinner

Adhesive glue type silicone

Adhesive glue type white glue

Adhesive glue type cooked glue powder

Adhesive glue type 801 Glue

Adhesive glue strong all-purpose glue

Electrical accessories wire tube

Electrical accessories wires

Electrical accessories telephone wires

Electrical accessories two-way video cable

Electrical accessories elbow tee

Hardware round nails

Hardware floor partition expansion Pipes

Hardware nails, mosquito nails

Hardware copper triangle valves

Hardware gas valves, gas pipes and accessories, elbow tees, gas valves Material tape, thick white paint, etc.

Basic material white cement

Basic material waterproof mortar

Basic material ceramic tile grout

Basic materials: cement

Basic materials: yellow sand

Basic materials: bricks

Auxiliary materials: bandages

Auxiliary materials Snake belt

Auxiliary material broom

Auxiliary material catalpa

Auxiliary material textured paper

Auxiliary material waste silk

Auxiliary material: sand leather

Auxiliary material: elastic putty

Auxiliary material: brush

Auxiliary material: talcum powder

Auxiliary materials: gypsum powder

Auxiliary materials: kitchen and bathroom imported marble doorsteps

Other auxiliary materials

Total price of auxiliary materials

Representative of Party A: Representative of Party B:

Year, Month, Day

Attachment 3:

List of Materials Purchased by Party A

Party A:

Party B:

Name Quantity Remarks

Wall and floor tiles

Sanitary ware matching sink

Hygiene Sanitary ware

Kitchen and bathroom faucets

Kitchen and bathroom ceiling aluminum gussets and light steel keels are installed by manufacturers

Cabinets and accessories

Kitchen sinks

Laminate flooring manufacturer installation

Water heater

Bath heater

Molded door

Enclosed balcony

ppr water pipe

Category 5 network cable, crystal head

50 fever cables

Eight ports

hub

Socket switch panel

Socket cassette

Kitchen sliding door

Main bathroom glass material

Door clip , hinges, sealing strips

Porch glass materials, borders

Background wall glass materials, advertising nails

Mirrors

Main bathroom waterproof Haiji Full set of construction by cloth manufacturer

Sofa background Haiji cloth manufacturer pasted

Lamps

Door locks

Door catch

Door hinges

Floor drains

Bathroom hardware

Coat hangers

Shower curtains

Curtains and rods

Latex Paint

Roller

Representative of Party A: Representative of Party B:

Year, Month, Day

Attachment 4:

Project Quality Acceptance Form

Party A:_

Party B:_

Date Inspection Item Name Inspection Result Inspection Signature

Re-inspection of qualified and unqualified

Water and electricity

Carpentry

Masonry

Painter

Installation project

Preliminary Clearance

Acceptance Opinions

Overall Project

Representative of Party A: Representative of Party B:

Year, Month, Day

Note: (1) Sub-item inspection assessment: Mark “√” if qualified, “×” if unqualified, and “√” if qualified for re-inspection.

Attachment 5:

Project Settlement Statement

Party A: __________

Party B:_ __________

Date Signature of both parties for project payment and material payment

1 Yuan Yuan

2 Yuan Yuan

3 Yuan Yuan

4 Yuan Yuan

5 yuan yuan

6 yuan yuan

7 yuan yuan

8 yuan yuan

Total yuan yuan

Year, month and day

Attachment 6:

Construction process list

Construction points for laying ceramic floor tiles

2. The line should be elasticized before pasting, and a reference line at right angles to the doorway should pop up on the ground. The elastic line should start from the door to ensure that the entrance is a whole brick. Non-integral bricks should be placed in the inner corner or under the furniture. The elastic line should be positioned vertically and horizontally. control line.

3. Before laying ceramic floor tiles, the ceramic floor tiles should be soaked and dried in the shade.

4. When paving, apply the evenly stirred ceramic adhesive fully on the back of the ceramic floor tiles, and tap it firmly with a rubber mallet after paving. At the same time, use a level to check the correction and wipe off surface stains.

5. 2 to 3 hours after paving, wipe the seams with white cement and use caulking agent. The seams should be filled densely, flat and smooth. Then wipe the surface clean with cotton wool.

6. Things to note.

(1) The base layer must be properly treated and there must be no floating soil or ash.

(2) Ceramic floor tiles must be soaked and then dried in the shade. It will not affect its condensation and hardening, causing problems such as hollowing and shelling.

(3) After the paving is completed, no one is allowed inside for 2 to 3 hours. Ceramic mosaic tiles should be cured for 4 to 5 days before they can be installed.

Veiner wall decoration process flow

(1) Basic veneer decoration process process

1. Paste glazed tiles:

Clean the base layer → apply primer → select bricks → soak → arrange bricks → elastic line → paste standard points → paste tiles → joints → wipe joints → clean.

2. Paste ceramic mosaic tiles:

Clean the base layer → apply base dust → arrange the bricks and elastic lines → paste → remove the paper → wipe the seams.

3. Construction points

1. When treating the base layer, all kinds of dirt on the wall should be cleaned up and watered one day in advance. The raised parts of the concrete wall should be chiseled away, and the base layer should be chiseled to remove floating dust. After applying the base dust, when the bottom layer is 60 to 70% dry, lay out the bricks and elastic lines.

2. Standard points must be pasted before formal pasting to control the flatness of the pasting surface. During operation, the flatness should be checked with a ruler at any time. If it is not flat or straight, it must be removed and re-glued.

3. Ceramic tiles must be soaked in clean water for more than two hours before pasting. As long as the brick body does not bubble, take it out and dry it for later use.

4. When paving and gluing, when encountering pipelines, light switches, supporting parts of bathroom equipment, etc., they must be cut and matched with whole brick sets.

5. After inlaying, clean the surface with cotton wool, and then wipe the seams with white cement slurry. Use caulk to caulk.

4. Precautions

1. The base must be clean and free of floating soil and dust. The original mortar surface of the old wall should be cleaned.

2. Ceramic tiles must be soaked and then dried in the shade. Because after the dry board is laid, the mortar moisture will be quickly absorbed by the board, causing dehydration of the cement mortar, affecting its coagulation and hardening, and causing problems such as hollowing and shelling.

Wood paint construction process

1. Main construction technology

Mixed-color paint construction technology:

First clean the dust on the surface of the base layer, repair the base layer → smooth it with sandpaper → apply paint chips on the knots → apply putty → Apply dry oil → apply putty for the first time → polish → apply the base coat → dry and harden the base coat → paint the surface layer → reapply the putty for repair → polish and wipe the third coat and apply the second coat Paint → Polish → Third coat of topcoat → Polish and wax.

2. Construction points

Construction specifications for varnish painting

Sanding the base is an important process for applying varnish. Dust, oil and other impurities on the surface of the wood should first be removed.

Applying oil powder is also an important step in varnish painting. During construction, dip cotton silk in oil powder and apply it on the surface of the wood. Rub it back and forth with your hands to rub the oil powder into the wood. Inside.

When applying clear oil, hold the oil brush in a relaxed and natural manner, and apply gentle pressure with your fingers, so that the brush does not loosen or fall off when moving.

When brushing, you should follow the requirements of dipping more frequently, less oil each time, operating frequently, and brushing smoothly. Follow the requirements of first up and then down, first difficult then easy, left first then right, and first inside. Construction should be done in the order of back and outside and the operation method of horizontal brushing and vertical brushing.

.Construction specifications for oil-contaminated wood surfaces

When treating the base layer, in addition to cleaning up the debris on the base layer, local putty embedding should be carried out. When applying sandpaper, it should be along the wood surface. Pattern polishing.

Before painting the surface layer, paint chips (shellac paint) should be used to seal the knots with large color difference and wood resin. Dry oil or clean water should be applied to the base layer. When applying the dry oil layer, all parts should be brushed evenly without any omissions.

After the base oil is completely dry, apply the first pass of putty. After drying, polish with manual sandpaper, and then top up with high-strength putty. The putty must be picked up and not fall over. When applying surface paint, sand it with fine sandpaper first.

3． Notes

(1) The base treatment must be carried out as required to ensure that the surface paint will not fail.

(2) Clean the surrounding environment to prevent dust from flying.

(3) Because paints are toxic to a certain extent and have a strong irritating effect on the respiratory tract, ventilation must be paid attention to during construction.

The process of applying latex paint

1. Main construction technology

Clean the base layer → fill with putty, partially scrape the putty, and smooth it → apply the putty in the first pass and smooth it → scrape the putty in the second pass and smooth it → apply primer → paint First coat of paint → reapply putty, smooth → apply second coat of paint → polish and finish.

2. Construction Points

Basic treatment is a key link to ensure construction quality. The most basic condition is to ensure that the wall is completely dry. It should generally be left for more than 10 days. The wall must be smooth and putty should be applied at least twice to meet the standard requirements.

The construction methods of latex paint can be hand brushing, roller coating and spraying. When painting, you should operate quickly and continuously, and finish the painting in one go.

After the primer dries, it should completely cover the wall surface without blooming or bluing.

3． Notes

(1) The putty should match the performance of the paint, be solid and firm, and should not be powdered, peeled or cracked. Use water-resistant putty in wet areas such as bathrooms.

(2) Use a high-quality roller for construction, Master Paint Roller

(3) The construction temperature should be higher than 10 degrees Celsius. There cannot be a lot of dust indoors. Best to avoid rainy days.

Construction of circuit modification

1. Circuit modification process

Determine the location of the line terminal socket→mark the exact location and size on the wall→nearby Similar socket leads

2. Construction points for circuit modification

1. If the socket is on the upper part of the wall, slot vertically upward on the wall and install decorative corner wires to the top of the wall. Within the installation line;

2. If it is at the lower part of the wall, groove vertically downward to the bottom of the skirting board.

3. The groove depth should be consistent, and the groove line and top should be straight. The control line should be popped up on the wall first, and then the wall should be cut with a marble machine and grooved manually.

4. Protective casing must be added when installing the line. The casing connection should be tight and smooth. The inside of the corner should be cut at the right-angled corner. An arc-shaped interface should be cut on one side of the cut and then bent for installation.

5. After the wires are installed in the casing, wire fixing clips should be used to fix them in the wall and on the wall first, and then covered with plaster or covered with skirting boards or decorative corner lines.

Install lamps correctly