Powder spraying processing contract

With the continuous development of the spirit of the rule of law, people are paying more and more attention to contracts, and more and more scenarios and occasions require the use of contracts. The signing of a contract is the best standard for the rights and obligations between the parties. So how to write the relevant contract? The following is a powder coating processing contract template (selected 6 articles) that I have compiled for you. You are welcome to read it. I hope you will like it. Powder spraying processing contract 1

1. Project overview

1. Project name: Economizer anti-wear spraying project

2. Construction location: ____________ South side of the open-air warehouse of Thermal Power Branch Co., Ltd.

3. Total project cost: 1,780 yuan/㎡*66.03m=117,533 yuan

Capital letters: One Hundred, One Thousand, Seven Thousand, Five Hundred Three-three yuan (including 17% value-added tax)

4. Project date: February 10, 20____ - February 18, 20____

5. Construction content: Responsible for anti-wear spraying construction of economizer.

2. Settlement method and period:

1. The cost of this project includes material fees, labor fees, loading and unloading fees, transportation fees, labor insurance premiums, tool and equipment fees, and 17% value-added tax. Contract-related expenses such as special invoice fees, insurance and management fees.

2. Settlement method: 20,000 yuan (two hundred thousand yuan) is paid in advance for the project before the project starts. After the project is completed, it will be used for three months after acceptance, and the payment is 20,000 yuan (two hundred thousand yuan). The fourth The monthly payment is 20,000 yuan (twenty thousand yuan), the fifth month payment is 20,000 yuan (twenty thousand yuan), the sixth month payment is 19,903 yuan (one thousand nine thousand nine hundred and three yuan), and the remaining 15% is warranty 17,630 yuan in gold (one thousand seven thousand six hundred and thirty yuan).

3. Warranty period: The warranty period is two years, and cracks and surface peeling are not allowed within two years. During the warranty period, Party B is responsible for repairing quality problems caused by Party B's construction technology and materials for free. If it affects Party A's production and causes losses to Party A, Party A may deduct the warranty deposit based on the loss.

3. Project quality and acceptance standards

1. Party B must follow relevant national and industry regulations and regulations as well as the "Unified Standards for Quality Inspection and Assessment of Construction and Installation Projects" as construction and acceptance standards. And accept the supervision of Party A’s representatives.

2. Technical requirements and quality standards of this project:

(1) The acceptance shall be based on the quality standards required by the "Technical Agreement".

(2) The coating is uniform, smooth, and has no cracks, pores, peeling, or melting defects.

(3) Local random inspection of coating thickness meets technical agreement requirements.

3. Key quality points during the construction process must be inspected and accepted before proceeding to the next step.

4. Party A and Party B shall promptly inspect and accept the work. Party B shall bear the cost of unqualified rework and the construction period shall not be extended.

5. If the construction quality is affected due to unqualified materials provided by Party B, Party B shall bear the losses caused and the construction period will not be extended.

6. If Party B encounters a quality accident during construction, it shall promptly report to Party A and, if necessary, the local quality supervision department. The cost of rework shall be borne by Party B and the construction period will not be extended.

4. Responsibilities and obligations of both parties

1. Responsibilities and obligations of Party A

(1) Clarify Party A’s representative at the construction site who will be responsible for the performance of the contract. Supervise and inspect the safety, quality and progress of the project, and handle acceptance, change registration procedures and other matters.

(2) Assist Party B’s personnel to go to the business department to apply for relevant factory entry and exit certificates, and fully provide the working conditions required for the operation.

(3) Provide the construction site and necessary power interfaces for Party B’s personnel to work, and explain the precautions for use.

(4) Responsible for notifying Party B of the determined construction time. If there is any change, Party B must be notified three days in advance.

(6) Responsible for providing Party B’s workers with detailed explanations of relevant rules and regulations and safety precautions in the district and production workshop, reasonably arranging construction tasks, and assuming corresponding management responsibilities.

(7) During the construction period, Party A will inspect Party B’s construction conditions at any time, give warnings or stop any management problems, safety problems, and quality problems found, and have the right to punish Party B.

2. Responsibilities and obligations of Party B

(1) Appoint Party B’s representative at the construction site to be responsible for the performance of the contract. Organize construction as required, ensure quality and quantity, complete the contract content on schedule, and resolve various matters that Party B is responsible for. According to Party A's requirements, technical personnel will be dispatched to participate in the overall construction work and shall not affect Party A's maintenance progress.

(2) Before starting work, Party B must go to Party A’s Safety and Environmental Protection Department for safety education and sign a safety agreement.

(3) Party B shall provide safety and quality education to dispatched personnel when entering the factory, so that all dispatched personnel shall strictly abide by the rules and regulations of the factory and production units and relevant safety regulations, and shall be responsible for relevant quality, safety and occupational safety regulations. Health management responsibilities and obligations; if Party A's production is affected due to Party B's personnel disobeying Party A's management, Party B will be held responsible according to the extent of Party A's losses.

(4) Party B shall be solely responsible for any accidents such as personal injuries caused by Party B during on-site construction.

(5) Party B shall carry out maintenance in strict accordance with the construction technical requirements of the contract and ensure the quality and construction period of the maintenance. If Party B causes production losses to Party A due to Party B’s construction quality, technical problems and construction period, Party B must bear relevant responsibilities , and Party A has the right to punish Party B.

(6) During construction, the original building structure and various equipment pipelines shall not be dismantled or modified at will without the consent of Party A.

(7) Party B shall handle all tools, spreaders and machinery by itself.

(8) Before the project is completed and handed over to Party A, the party is responsible for protecting all on-site facilities and finished project products.

(9) Party B must designate a full-time safety officer. If a safety accident occurs during construction, Party B will be responsible.

(9) After the project is completed, the garbage generated must be cleaned up to keep the site clean.

5. Contract Period and Validity

1. Dispute Resolution Method

(1) Any disputes arising during the performance of this contract shall be negotiated by both parties. If an agreement cannot be reached, either party may file a lawsuit with the People's Court where Party A is located.

(2) All claims and debts involved in this contract shall not be transferred to a third party without the agreement of both parties.

2. The contract becomes effective

(1) This contract shall take effect from the date when the legal representatives or authorized representatives of both parties sign and affix the contract seal.

(2) This contract is made in four copies, written in Chinese, two copies for Party A and two copies for Party B.

(3) Place of contract signing:

(4) Date of contract signing

Party A:

Party B: Powder spraying Processing Contract 2

Party A (demand party):

Party B (supplier):

Signing time:

Signing place:

Party A entrusts Party B to carry out paint spraying in the area designated by Party A. After full consultation, the two parties have negotiated on the responsibilities and obligations of Party A's paint outsourcing and other related matters in line with the principle of "fairness and justice, win-win cooperation" as follows:

1. Party A's responsibilities and Obligations:

1.1 Party A shall, in accordance with the factory lease contract, provide the factory building and paint room, paint warehouse, air compressor equipment and other related facilities required for product processing, as well as production water and electricity (electricity charges are charged according to the meter) ; Party A is responsible for the food expenses of Party B's personnel, but Party B must promptly inform Party A's management department of the number of people dining, otherwise Party B will be responsible for any additional expenses incurred.

1.2 Party A will send the next month’s production plan (paint processing) to Party B before the 27th of each month to facilitate Party B’s production capacity preparation. All products to be sprayed will be processed on the premise that Party B can guarantee the progress and quality. Priority will be given to Party B for processing.

1.3 During the processing, Party B sets up its own inspectors who must be responsible for the processed products, conduct self-inspections and pass the inspection, and then apply for inspection. Party A has the right to inspect the products constructed by Party B based on the processing technology requirements. Supervise the process.

2. Responsibilities and obligations of Party B

2.1 Party B signs a factory lease contract with Party A and carries out painting processing in the designated area of ??Party A's factory. During the lease period, Party B is responsible for the maintenance and repair of the equipment provided by Party A, accepts Party A's unified requirements for equipment management and on-site management, and bears the corresponding consumables and other related expenses. When the cooperation is terminated, Party B shall organize the equipment provided by Party A. , and ensure that it is intact.

2.2 Party B is responsible for other necessary conditions except for the facilities provided by Party A in 1.1.

2.3 Party B and its personnel stationed in the factory must fully abide by Party A’s rules and regulations and accept Party A’s unified management. Party B appoints a person in charge or his representative to fully manage the safe production, food and accommodation of Party B’s personnel. And be responsible for coordinating the relationship with Party A. Any economic or other losses caused to Party A by Party B's personnel shall be borne by Party B;

2.4 Any labor disputes involving wages, work-related injuries, insurance, etc. that occur when Party B's personnel work at Party A's premises shall be borne by Party B. Party B is responsible for solving the problem and assuming relevant responsibilities.

2.5 Party B must carry out production according to the plan given by Party A, organize and manage the progress and personnel, accept Party A’s quality and progress assessment, and achieve safe and civilized production. All flammable and explosive materials must Dedicated area for safekeeping.

2.6 The occupational health protection and physical examination of Party B’s personnel are their own responsibility. Party A has nothing to do with any problems that occur to its personnel anywhere.

2.7 The water and electricity bills incurred by Party B’s personnel for accommodation shall be borne by Party B. Party A will notify Party B of this together with other expenses that should be borne every month and deduct it from the settlement payment of the month.

2.8 Party B is responsible for the disposal of solid waste generated during the paint processing process. Party B must provide paint processing solid waste treatment qualifications or provide proof of third-party treatment qualifications and a treatment contract. Party B must retain the treatment certificate and give it to Party A for preservation.

3. Progress and quality assurance

3.1 Party B arranges production according to the product processing cycle and Party A’s schedule requirements. At the end of the month, Party A will assess its monthly implementation. When delivery If the timeliness rate is less than 98%, a fine of RMB 500 will be imposed for every time it is less than 1%.

Delivery timely rate = (monthly total planned quantity - undelivered quantity)/monthly total planned quantity × 100%,

3.2 Product processing quality requirements, Party B shall do a good job in all aspects The control of the process shall comply with the product quality inspection standards provided by Party A's customers or relevant national industry standards, and the final acceptance condition shall be customer approval.

3.3 Product warranty period: The warranty period is based on the requirements of Party A’s customers and starts from the date Party B puts it into storage. During the quality assurance period, if Party A's customers raise quality issues such as repairs, returns, or claims due to the quality of Party B's products, Party B shall bear all costs and losses. For details, see the "Supplier Quality Assurance Agreement."

3.4 During the quality guarantee period, Party A must retain 100,000 yuan in the accounts payable to Party B as a quality deposit, which shall be paid off one month after the expiration of the product warranty period.

3.5 If the paint is damaged during assembly and transportation of the product due to Party A’s fault, the repair costs shall be borne by Party A.

4. Product delivery, settlement unit price and process

4.1 After Party B passes the self-inspection, Party B shall fill in the product model, processing batch, quantity, serial vehicle number and other data on the delivery form , after the receiving party signs, the sprayed products will be transferred to the relevant team of Party A’s production department until the finished products are qualified and put into storage.

4.2 The 25th of each month is the settlement day. The quantity of finished products that are stored in Party A’s warehouse (processed by Party B) in that month is used as the monthly settlement quantity, and it shall be the effective quantity after being approved by Party A’s production department.

4.3 As agreed by both parties, the unit price of paint processing for various products will be calculated according to Party A’s paint pricing standards (different paint brands will be multiplied by corresponding coefficients based on different requirements based on the standard value). (See the attachment for the specific processing unit price of each product)

4.4 Party A specifies raw and auxiliary paint materials (primer, intermediate paint, topcoat, curing agent, thinner, putty, sandpaper, grinding disc, etc.) brand.

In early April, Party B will reconcile the paint outsourcing processing order issued by Party A with Party A’s purchasing department. After confirmation by both parties, Party B will issue a processing value-added tax invoice (17%) and submit it to Party A. The payment procedures will be processed 90 days after the account has been placed (deducting the amount payable by Party B to Party A in the current month).

If a product is returned due to quality problems, the quality deduction will be deducted from the amount payable this month.

5. Liability for breach of contract

5.1 Party A promises to pay Party B’s payment within the settlement period. If payment is delayed due to special reasons, Party A shall communicate and negotiate with Party B in a timely manner.

5.2 Party B promises to guarantee Party A’s delivery period, quality and other terms required by the agreement, and accepts relevant assessments.

5.3 If the processed parts submitted by Party B are defective and cause Party A’s production line to stop working, Party B will be responsible for the loss of working hours. If it causes very serious adverse consequences to Party A, Party A has the right to cancel its processing. Qualification, stop paying the payment due.

5.4 Due to other reasons, Party B requests to stop cooperating with Party A. Party B shall submit a written withdrawal report 60 days in advance, otherwise it will compensate Party A for liquidated damages of 100,000 yuan. Before formally withdrawing, Party B shall continue to strictly perform all obligations under this Agreement.

6. Others

6.1 All attachments to this agreement have the same legal effect. During the performance period, if a dispute occurs or any party breaches the contract, the two parties will negotiate to resolve it. If the solution is not resolved properly, The dispute shall be submitted to the relevant institution where Party A is located for arbitration in accordance with the provisions of the Contract Law.

6.2 The agreement is valid for one month. From then on, Party B shall formally propose its intention to renew the contract.

6.3 Matters not covered shall be negotiated and confirmed by both parties. This agreement is made in two copies, with each party holding one copy. It will take effect from the date of signature by both parties.

Party A: Party B:

Company name (chapter): Company name (chapter):

Company address: Company address:

Legal representative: Legal representative:

Authorized agent: Authorized agent:

Telephone number: Telephone number:

Account opening bank: Account opening bank:

p>

Account number: Account number:

Tax number: Tax number:

Postal code: Postal code: Powder spraying processing contract 3

Party A:

Party B:

During the production process of Party A, some workpieces need to be painted. After inspection, Party B is determined to be the processing partner. After full negotiation between the two parties, the following agreement was reached on cooperation matters:

1. Party B must have all qualifications for spray painting processing.

2. Processing cooperation period: from ____ month ____ day ____ year to ____ month ____ day ____ year.

3. During the cooperation period, Party A shall supervise and inspect the quality and supply capacity of the processed parts contracted by Party B.

IV. Party B must produce according to the production order issued by Party A. Without Party A’s permission, Party B shall not transfer production to other units.

5. Party B processes workpieces for Party A, and in principle implements the method of contracting work and materials.

6. The price of the products Party A entrusts Party B to process shall be based on the price verified in Party A’s order or the price list negotiated by both parties, and no party may change it without authorization.

7. Settlement method agreed upon by both parties: Settlement after each batch is completed.

8. This agreement shall be effective when stamped or signed by both parties, in duplicate, and shall be legally binding.

Party A: Representative:

Party B: Representative:

Signing date: ____ year ____ month ____ day Powder spraying processing contract 4 < /p>

Party A:

Party B: ID number: (Attach a copy of ID card)

In order to invigorate the mechanism, improve economic benefits, improve workshop efficiency, and ensure The workshop process is smooth. Party A and Party B have now decided through negotiation that the painting process of Foshan Baoyue Automobile Maintenance Service Co., Ltd. will be contracted by Party B. In order to safeguard the legitimate rights and interests of all parties, after consensus reached by both parties, this contract is signed as follows:

1. Party A will contract the ____ brand and other similar-level models to Party B at a price of 250 yuan for a single frame of paint, and Subaru and other similar-level models at a price of 180 yuan for a single frame of paint. The price will be contracted to Party B for the process. Finish.

2. Party A pays Party B: the price of half-frame painting is 150 yuan/half frame, the price of steel bell is 150 yuan/piece, the price of electroplated silver steel bell is 300 yuan/piece, and the price of full car polishing is 250 yuan Yuan/Taiwan.

(Subaru's half-spray of the same level is 108 yuan/half-spread).

3. A. Front and rear frosted parts, A, B, C pillars, half commission (free rearview mirror shell spray painting)

B. Total vehicle refurbishment, 16 pieces Paint; 20 pieces of paint for color change; wheel eyebrows 50 yuan/piece

C. If the paint surface is damaged due to Party A’s assembly process, it will be semi-sprayed (____ brand 150/half frame, Subaru equivalent level 108 yuan/half width)

D. Party B is responsible for any damage to the vehicle caused by Party B.

4. Party B is responsible for the paint materials and auxiliary materials of ____ brand or the same level of vehicle models, and specifies the use of Spies Hecker paint.

5. Party B is responsible for and uses the paint materials and accessories for Subaru and equivalent models (Party A needs to supervise).

6. Party A is responsible for providing Party B with a paint room, water, electricity, newspapers, and diesel, and Party A shall pay the costs. Party B must take good care of Party A's equipment and tools during the contract period. Party B will be responsible for equipment damage other than normal wear and tear. After the contract period is over, they must be returned to Party A in complete condition.

7. Party B will provide Party A with a half-year quality maintenance period after delivery of the vehicle (excluding artificial costs).

8. Party A provides Party B with a guaranteed salary of RMB 10,000, that is: the total amount of processing - the cost of paint accessories paid by Party A = the amount paid by Party A to Party B (if it is less than RMB 10,000, it will pay RMB 10,000 Yuan). Payment must be made before the 15th of the following month.

9. Party A will provide Party B with two meals a day (10 yuan/meal) and accommodation in a dormitory. Calculated based on attendance and clocking in.

10. Party B is responsible for the purchase of personal insurance and labor management of the painting staff. Ensure the orderly management and production safety of the spray paint workshop, and strengthen fire safety. And establish a production safety system to conduct production safety training for employees. During the contract period, if production safety accidents, traffic accidents, fire accidents, employee violations of laws and disciplines, etc. occur in the spray paint workshop, Party B shall bear all the responsibilities and compensate Party A for the property losses caused.

11. Neither party shall unilaterally terminate the contract in advance, otherwise it will be deemed as a breach of contract, and the defaulting party shall pay liquidated damages of RMB 30,000 to the non-breaching party (except for force majeure and Party A’s suspension of operations).

12. This contract shall be from April 22, 20____ to April 21, 20____. Unfinished matters shall be resolved through negotiation between the two parties. As an attachment to this contract, it shall also have legal effect. .

13. This contract shall come into effect upon signature by both parties, with Party A and Party B each holding one copy.

Party A:

Party B: Powder Spraying Processing Contract 5

Party A:

Party B:

In order to better manage the spray paint workshop, improve production efficiency and reduce spray paint (powder) costs. After mutual negotiation between Party A and Party B, it was decided that the spray painting workshop would be contracted and operated by Party B. In order to clarify the rights and obligations of both parties, this contract is hereby concluded:

1. Contract subject:

Party A’s spray painting workshop

2. Contract period:

p>

From ______month______day of ______year to ______month______day of ______year

3. Rights and obligations of both parties:

< p> (1) Party A’s responsibilities:

1. During the contract period, Party A will settle the settlement with Party B based on the surface area of ??the parts. Regardless of painting or powder spraying, the settlement will be based on ______ yuan/m2.

2. Party A provides the site, spraying line, water, electricity, etc. The spraying line, crane, electricity, and lights are maintained by Party A, and the other production tools are maintained by Party B.

(2) Party A’s authority:

1. Party A has the right to conduct various administrative management of Party B, such as health, safety, etc. Smoking is prohibited in the workshop to avoid the occurrence of fire. If an accident occurs as a result, Party B will be responsible for all losses.

2. Party A has the right to supervise Party B’s production environment and labor protection. Party B is prohibited from using bituminous coal. Personnel who spray, spray and polish parts must wear corresponding protective tools. Party A discovers that Party B In case of violations, the company has the right to terminate the contract or impose financial sanctions.

3. Party A assigns production tasks to Party B on a monthly or temporary basis. Party B shall ensure quality and quantity and complete production tasks on time according to Party A’s requirements. Party A has the right to impose financial penalties on Party B for delayed delivery. Party B will be deducted 100 yuan for each delayed part that affects the production schedule, and all costs caused by Party A's delay in shipping schedule will be borne by Party B.

(3) Party B’s responsibilities:

1. During production and operation, Party B must obey Party A’s management, complete the production tasks assigned by Party A in a timely manner, and follow all Party A’s rules and regulations. system produces.

2. All required production supplies shall be borne by Party B, and invoices shall be issued to Party A.

3. Party B shall produce according to Party A’s quality standards and control the quality of materials used. The paint, powder, thinner, curing agent, etc. purchased by Party B must comply with ROHS requirements, otherwise all consequences will be serious. shall be borne by Party B.

4. Party B is responsible for regular maintenance and upkeep of the equipment and facilities provided by Party A. Any abnormalities in the equipment should be reported as soon as possible. Party B shall bear the responsibility for equipment damage caused by Party B’s operating errors.

5. Party B must provide the monthly purchase invoice to Party A before ______ day of each month, and Party A will calculate the processing fee based on the invoice and Party B’s output. Party B must provide an invoice (______) for the processing fee to Party A, and Party A will pay Party B according to the invoice amount that month. If Party B cannot provide corresponding invoices in time every month, Party A has the right to refuse settlement.

6. Party B shall not privately accept the supply of goods from other units. Once discovered, a fine of 100 yuan will be deducted each time.

7. Party B is responsible for the personal safety of all personnel in the spray painting workshop. If an accident occurs, Party B will be responsible for it, and Party A will not bear any responsibility.

8. Party B shall not subcontract the workshop to others during the contract period.

(4) Party B’s authority:

1. During the operation period, Party B shall operate independently and bear its own profits and losses.

2. During the operation period, the equipment, tools, paint, powder, etc. purchased by Party B will be owned by Party B upon expiration.

(5) Others:

1. If the contract is to be renewed or terminated at the end of the contract period, both Party A and Party B shall notify the other party one month in advance.

2. Matters not covered in this contract shall be handled in accordance with relevant laws.

3. This contract is made in two copies, with Party A and Party B each holding one copy. It will take effect after both parties sign and seal it.

Party A (signature of representative): Party B (signature of legal person):

(Official seal) (Official seal) Powder spraying processing contract 6

Party A: ____ Company

Party B: ____Spray Paint Factory

Party A and Party B have determined through friendly negotiation that Party B will be Party A’s spray painting processing point. Party B guarantees to complete the work plan required by Party A on time and with high quality and to provide products that meet the requirements.

1. Specific product name, spray paint color and spray paint price:

Based on the price list signed by both parties.

2. Technical terms:

1. The paint must be environmentally friendly paint, and Party B needs to provide relevant environmental protection documents to Party A.

2. The appearance of spray-painted products must be flat and smooth, and there must be no defects such as particles, spots, protrusions, scratches, burrs, etc. that exceed the inspection standards.

3. All parts requiring painting must be painted in place.

3. Inspection method:

After Party B self-inspects the products and completes packaging, it submits an inspection report to Party A’s quality department, and Party A’s quality department inspectors will go to Party B’s factory to inspect the goods. . Party A's quality personnel conduct random inspections based on inspection standards. If the defective product rate is equal to or higher than 3%, Party A has the right to require Party B to rework and submit for inspection again. Party A has the right to impose reasonable penalties on Party B if it is reworked twice or more. (Except if Party A requires Party A to send its own personnel to 100% inspect the goods.)

4. Delivery terms:

According to the requirements in the "Production Plan" approved by both parties Delivery time of painting completion. When the product is accepted and delivered, Party B submits the delivery note to Party A's warehouse for signature and confirmation and applies for warehousing, and Party A decides the delivery date. In case of special circumstances, both parties shall negotiate and resolve the matter.

5. Transportation and packaging terms:

Party B will automatically come to pick up the goods. If there are special circumstances, Party A should assist Party B in handling transportation matters.

Party A provides the packaging, and Party B shall be responsible for the packaging provided by Party A and package the products in strict accordance with Party A’s packaging requirements.

6. Payment terms:

Party A will pay the monthly settlement within 60 days after Party A passes the inspection.

7. Obligations and liability for breach of contract by Party A and Party B:

Party A shall provide sealed sample products and technical requirements to Party B. Party A is obliged to pay Party B the payment on time. Party B shall strictly follow Party A's technical requirements and sealed sample production. If the product fails to meet Party A's technical requirements and sealed sample requirements and causes the product to be scrapped, Party B shall pay Party A for the loss of raw materials and working hours.

If Party A’s delivery is delayed due to Party B’s fault, all direct losses of Party A shall be borne by Party B. If Party A's goods are fined due to Party B's quality reasons, Party B shall bear the fine costs.

8. Other terms:

Party A and Party B must abide by the above agreement, which is based on contract law. If the two parties cannot negotiate at that time, the superior authority will assist in solving the problem.

This contract is made in two copies. Party A and Party B each hold one copy. The signatures and seals of representatives of both parties are effective. This contract is valid for one year, starting from the date of signature by both parties. If both parties have no objection after expiration, the validity period of the contract will be extended until one party formally requests termination.

Unit name: Unit name:

Unit address: Unit address:

Legal representative of Party A: Legal representative of Party B:

Telephone: Telephone:

Fax: Fax:

Account opening bank: Account opening bank:

Account number: Account number:

Year 20____ ____month____day ____month____day 20____year