What is the reason why the sliding door is not smooth after the shower room is installed?

One. The problem of bottom leakage is caused by uneven stone foundation and ground, which can be solved by glass glue; If there is water seepage on the front of the glass, the installation angle and waterproof glue are not sealed properly.

Two. If the overall structure is reasonable, there will generally be no problems (of course, if the glass is tempered with good quality), and there will be problems during installation, which will only lead to the service life of the product.

Three. Can only be installed on the wall.

1. Glass glass is divided into ordinary glass, hot bending glass, strengthened glass, semi-toughened glass and fully toughened glass. In the choice of shower room glass, in order to ensure the safety of consumers, completely toughened glass must be strictly used. Tempered glass also has many differences. First of all, it depends on the equipment, technology, technology and management of the original glass factory. The original glass plate is made of silicate. If the equipment, technology and process of the original glass sheet factory are not up to standard, the original glass sheets produced will have bubbles, pinholes, black spots, white spots and fog. Among all the original glass processing plants in China, only Shanghai Yaopi Company and Shenzhen Nanfang Glass Factory have the most advanced production equipment and technology, and the original glass produced has less impurities and good air permeability, which are supplied to Audi, Guangzhou Honda and other automobile manufacturers. In addition, in the process of tempering raw glass, it is required that the equipment, technology and management of the tempering plant should be excellent. In the heating process, the optimum temperature of tempering furnace is about 695 degrees. If the temperature is too high, the glass strength is low, fragile and too low, and the broken glass particles are uneven, even very large and sharp, leaving a safety hazard. The national standard for tempered glass is 50×50, with an area of ≥40 pieces. Nowadays, many shower room manufacturers who don't pursue quality choose some manufacturers who produce architectural glass or manufacturers whose quality is not up to standard in order to control costs. Because of the limitation of equipment and scale, where can we talk about quality?

Low-grade shower rooms generally use tempered glass for buildings, so the purity of the glass is low, and there are small pinhole-shaped black spots and bubbles on the surface, so the permeability is not high. In addition, the tempering coefficient of glass is also low, the tempering is uneven, and the appreciation is sharp, with less than 40 grains per 50×50 area, leaving a safety hazard. So when distinguishing glass, clean it with newspaper. Careful observation with the naked eye will reveal that the above defects still exist in low-grade shower rooms.

2. Alloy aluminum is a metal element extracted from aluminum ore. Canada is the best producer of aluminum ore in the world, followed by China and Australia. There are many bases for producing aluminum mines in China, such as Guizhou, Shanxi and Gansu, among which Guizhou's aluminum mine is the best. Aluminum in Zhongshan, Guangdong Province is a combination of aluminum ingots in Guizhou, China and aluminum ingots in Australia-commonly known as Zhongshan Aluminum. Zhongshan Aluminum has a high reputation in the aluminum industry, which belongs to industrial grade aluminum and is a national inspection-free product. In Nanhai, Foshan, Guangdong, there are a large number of aluminum materials for construction. Most of these aluminum materials are processed by low-priced aluminum ingots, and the recycled waste aluminum materials are used for secondary processing. In order to reduce the cost, some low-grade shower room manufacturers use this aluminum material as a shower room.

Methods of comparing aluminum materials: a, whether there are color differences, lines and trachoma from the poor quality surface treatment; B, see if the aluminum incision is shiny, smooth and burr-free. A good aluminum notch is shiny, smooth and burr-free. On the contrary, it is low-grade aluminum, which will be soft if you pinch it hard; C hang the weight of the whole body on the beam of the shower room to prove endurance.

Step 3 pulley

Pulley is the most important thing in push-pull shower room. Only pulleys with reasonable structure and good material can ensure the service life of shower room and the safety of consumers.

Some high-end shower rooms are designed with double pulley trapezoidal and V-shaped tracks. V-shaped track design, not easy to wear, no space, no shaking. There are roughly the following types of pulleys used to resist the shower room: A. Carbon steel pulleys-these pulleys are easy to rust, break and corrode, and the load-bearing part of the pulley is black and coated with white glue. B, zinc alloy pulley-this material is also easy to rust, fragile and easy to break, and the rubber outside the pulley falls off after severe friction. C, copper shaft rubber-coated pulley design-this kind of pulley is the most common, the middle part is brass, the inside is steel ball, and the outside is white PVC material. The friction between copper and steel balls and plastic is easy to wear, the pulley gap is large, and dust can easily enter and jam the steel balls, resulting in the damage of the rubber-coated pulley.

4. Look at the overall structure and hardware of the shower room-some high-end shower rooms pay great attention to the design of drainage and adjustment functions in structure. If they have the function of adjusting the vertical and horizontal direction of the wall, they can correct the deviation caused by cement workers and installers. The hardware fittings of high-grade shower room are mostly stainless steel fittings, and 304 hand-polished stainless steel is the best.

The common faults of some low-grade shower rooms are as follows: a. The track design adopts a 90-degree U-shaped design, and the bottom rail is also a U-shaped groove design, which is easy to accumulate dust and wear pulleys. B, there is no adjustment function before and after, the deviation of the cement worker can't be corrected, the installation effect of the shower room is not good, the glass is easy to explode when it is twisted sideways, and the pulley is easy to wear. C, all fittings are made of low-cost aluminum alloy fittings and zinc alloy fittings, and even plastic parts are used as supports, which are not only unstable, but also easy to wear and break. D, there are many burrs at the aluminum joint, which are uneven and rough as a whole.

5. Tape and its sealing performance-The quality of tape lies in the quality of raw materials and the control of processing technology. At present, the best tape for shower rooms in China is PVC tape, which is suitable for cold winter and hot summer, and its weather resistance and aging resistance exceed the industry standards. At present, a good shower room has soft adhesive tape on the aluminum edge, which can reduce the glass glue and achieve good sealing.

Some low-grade shower rooms are not well designed in the treatment of water strips at the bottom of the door, and water leakage often occurs. In addition, a considerable number of flat doors designed by shower room manufacturers all use spring hinges, and the hinge part needs to be cut, which leads to the fact that the upper and lower rubber strips are not a whole and the hinge part leaks seriously. In a word, the door sealing magnetic strip and sealing rubber strip used in low-grade shower rooms have poor quality and technology, poor air permeability, many impurities, easy aging and fracture, and short service life.