A seamstress must know how to sew the wall beautifully.

Before joint construction, make sure that there is no empty drum and weak adhesion of the bathroom tiles, then clean the joints to keep the joint depth of the tiles at about 0.5- 1.5 mm, and then clean the dust and other impurities in the joints with a rag or a fine brush. Put the caulking agent into the glue gun, slowly and forcefully spread the material evenly in the joint, scrape the material in the joint with a scraper as soon as possible after painting, so as to achieve a smooth and bright surface, and try not to let the caulking agent overflow the outside of the brick joint when scraping.

A, wall joint method:

1, the principle of top-down, first horizontal and then vertical is generally adopted when the wall is used as joint sealant. Novices strongly recommend textured paper, which is tiring but the effect is guaranteed. It's best to stick a cross with masking paper. After sewing one seam horizontally, sew the seam vertically. Due to the influence of gravity, the sewing agent will automatically flow downward, which is very easy to operate.

2. The principle of high before low: finish the upper part of the sealant first, and then lay the lower part, so that the lower part will not be destroyed because of the construction of the upper part, which can save a lot of manpower and material resources. The cut of the mixing tube should not be too small or can't be punched out, just have the gap size of the ceramic tile. After the sealant is finished, scrape it clean with a scraper. Scrape hard. Be sure to scrape it with a scraper before solidification, and tear off the lines as soon as possible after scraping.

3. After cleaning up the gap, you must paste masking paper. One person glues the glue and the other scrapes the paper, so the work is done quickly and well. Finally, some spills can be shoveled away when they are dry. Very smooth, beautiful color, very economical and convenient.

4. When the wall is beautifully stitched, the stone to be used and the caulking agent for filling the stone should be prepared first, and then the base surface of the wall should be soaked with clear water. Only when there is no clear water on the surface can the bonding construction be carried out. Make sure that there is no Mingshui on the base surface, and then scrape the special artificial stone glue with a thickness of more than 3mm. In the same way, the back of the stone is 2-3 mm, and then paste the stone.

5. Be sure to paste the stone within the specified time. When pasting, twist the stone gently, rub it up and down or tap it with a mallet. This is to make the stone closely fit the adhesive. For wall paving, the construction team of ceramic tile caulking agent can also add copper wire to fasten it according to the design requirements. Correct the joints between horizontal plates and adjacent plates. Pay attention to leave a seam of more than 2mm between stones.

6. Initially clean the dirt attached to the surface of the plate, and clean it and caulk it after 3 days of pasting the stone (according to the relevant instructions). Professional caulking agent should be used when caulking. Clean up after caulking treatment, and clean up the excess caulking agent on the surface of ceramic tile before it is dry.

7. If it is a new tile, the gap between the corner and the brick joint should be filled with caulking agent, and then the gap between the corner and the brick joint should be wiped clean (the width of the brick joint is at least 1mm, the depth is 1-2mm, the antique brick is 3mm, and the depth is 1-2mm), and the gap must be clean and flat. For old tiles, the tile sealant should be shoveled off with a utility knife. The joint width is at least 1mm, the depth is 1-2mm, and the antique brick width is 3mm, 1-2mm. Joints must be clean and level.

8. Apply the sealant between the corner and the brick joint, wipe out a line with moderate radian and the same size as the wall gap with your fingers, and then smooth it with seawater. Sponge should not be too wet, master the degree and make the thickness of online and offline consistent, so that the effect is three-dimensional.

Second, matters needing attention:

1. After the tiles are pasted, clean the surfaces and gaps of the tiles, dry them without dust, and then fill them with this product.

2. Open the aluminum bottle with a hard object.

3. Screw the nozzle on the aluminum bottle mouth.

4. Cut the concave and convex on the top of the nozzle into a 45-degree angle with a knife. The width of the nozzle is slightly smaller than the brick joint. Due to the different sizes of brick joints, the width of the nozzle should be treated according to the specific situation.

5. Open the pull ring at the bottom of the sealant. Put the caulking agent into the glue gun, and use the glue gun to evenly inject the material into the brick joints.

6. Scrape the material flat with your fingers or scraper.

7. Clean excess materials on the surface of ceramic tile with a wet sponge.

8, two hours after the completion of the construction surface maintenance, two days after the normal use.

9. Be sure to do a good job of cleaning before making a beautiful sewing agent, and clean the tiles before making a beautiful sewing agent.

10, when sewing, you must make a straight line. You can punch horizontally first and then vertically.

1 1, the force must be uniform when applying the sealant, and be careful when wiping with a wet sponge.

12. When there is a pause, be sure to wipe the discharge nozzle with a newspaper, and then block the discharge nozzle with a toothpick.