What should I do if the latch of the door and window is too short when the new house is accepted?

You can consult the developer, and it is best for the developer to sign the house inspection form for confirmation, so as to prevent the developer from playing tricks and refusing to recognize the account.

Six common problems in door and window acceptance and their solutions;

1, the acceptance dimensions of doors and windows do not meet the design specifications.

If the design in the early stage is unreasonable, it is often difficult to rectify it in the later stage, which will also bring a lot of inconvenience to the owner's future life. For example, the design of doors and windows has strict requirements in the specification, but in the process of house inspection, it was found that the doors and windows of some real estates were not designed according to the requirements, which left problems for the owners' later decoration or life. The entrance of Mr. Luo's new house is too narrow, with a width of only 76 cm, which does not meet the requirement of the Code for Residential Design that the minimum width of the entrance is 90 cm.

Raiders of house inspection: when the owner accepts the house, he should take a tape measure to measure whether the size of the door opening and window is consistent at any time and anywhere. Once the design is found to be defective, he should find the developer to take remedial measures in time.

2. There is no drain hole in the bottom frame of doors and windows acceptance.

Judging from the house inspection last month, another outstanding design defect is that the bottom frame of doors and windows is not provided with a drain, which has occurred in many real estates. If it is not found and rectified in time, once it rains, the rain will penetrate into the bottom frame of doors and windows and cannot be discharged in time. The accumulated water formed by rainwater will corrode the door and window frames and shorten the service life of doors and windows.

Raiders of house inspection: if the owner does not inspect the house, the installation problem will be left to the owner, and the problem will be discovered only when the decoration moves in. Then who are you going to see? Therefore, the owner should carefully check every part of the house when inspecting the house, and ask the developer to come over for rectification in time when problems are found.

3. Acceptance of doors and windows, no drip line at the top of the window.

Some parts of doors and windows have special construction requirements, which must be put in place in accordance with relevant regulations. If it is at the outer edge of the window, drip line is required to prevent rainwater from flowing into the window sill or indoor wall. However, in the process of house inspection, it was found that many buildings did not do drip line as required because of the window sill, which led to rainwater infiltration into the room. If it is not rectified in time, the rain will still seep into the room along the windowsill when it rains in the future, and it is inevitable that the wall will be wet, moldy and hairy over time.

Raiders of house inspection: the leakage problem will have a great impact on the decoration of the house and the future life. Doors and windows are also one of the leakage sources of houses. When the owner closes the house, please be sure to check it carefully, leaving no hidden danger of leakage.

4. There is no sealant between the door and window acceptance frame and the wall.

According to the Code for Quality Acceptance of Building Decoration and Decoration in Wuhan, the gap between metal door and window frame and wall should be fully embedded and sealed with sealant. However, in the "Home Inspection", it was found that the doors and windows of many buildings were either leaking sealant or the sealant was incomplete. This not only affects the sealing performance of doors and windows, but also easily causes rainwater to seep into the room when it rains, thus damaging the indoor decoration.

Raiders of house inspection: this kind of problem is often easily overlooked when the owner closes the house. After the renovation, I found that I was in big trouble, so I had to find a developer to replenish the sealant.

5. There is no safety glass installed in the lower frame of window sash for door and window acceptance.

For safety reasons, there are also hard and fast rules for the installation of window glass. According to the "Regulations on the Management of Building Safety Glass", safety glass must be used for the glass whose bottom edge is less than 50 cm from the final decoration surface. At present, many units are designed with bay windows, but it is difficult to find the 3C logo on the fan-shaped glass fixed under the bay window. This is not a safety glass, which has potential safety hazards.

Raiders of house inspection: Door and window glass is related to personal safety. If the owner can't see the 3C sign on the fixed fan glass under the bay window, he must ask the developer to show the certificate of precautions for house inspection or the certificate of material purchase inspection. If it cannot be proved to be safety glass, it must be replaced.

6, doors and Windows deformation acceptance

Deformation of doors and windows is also common in house inspection. For example, the window frame is sunken, the door frame is damaged, the door leaf is scratched and so on. These are all caused by the carelessness of workers in the installation process or the carelessness of finished product protection. These problems may affect the beauty of the finished product, and even lead to the failure to completely close the doors and windows, which has potential safety hazards.

Note: the acceptance of doors and windows is a very important step in the process of house inspection by buyers. If the problems of doors and windows are not found and solved in time, it will bring unnecessary trouble to the buyers' future residence.