Who designed and printed the Residential Property Delivery Acceptance Sheet, and what is the specific content?

I. Relevant documents

Check the contract to see if the agreement in the annex is in line with the actual situation. Commercial housing pre-sale contract, residential instruction manual, residential quality guarantee and completion acceptance record form.

Second, the entrance door

1: Check whether the door body of the entrance door is bumped or scratched, and whether the door seal, decorative cap and other accessories are installed.

2. Whether the paint surface of the entrance door falls off, is smooth, has the same color and has no rust.

3. Whether the lock of the entrance door is flexible, firm, easy to operate and evenly locked.

4. Whether the door shaft is smooth and firm, and whether it rotates smoothly.

5. Installation of door frames and fans, combination of fans and frames, and sealing performance.

6. Whether foaming agent is filled between the door frame and the wall, and whether neutral silicone sealants is applied.

7. Whether the cat's eye is intact and the field of vision is clear.

8: Whether the doorbell button is in good condition and there is sound when it is powered on.

9: Variety, type, specification, size, opening direction and installation position of the door.

Third, indoor doors and windows engineering

1: Whether safety glass is used when the single glass is larger than 1.5 square. Buildings with seven or more floors must use safety glass.

2. Whether the sliding window is equipped with an anti-falling device.

3. Whether the sliding window is equipped with anti-collision blocks.

4. Whether there are drainage holes in the lower frame track of sliding window.

5: Check whether all windows and sliding door profiles are deformed.

6: Check the surface of the window glass for scratches, damage, bubbles, sand holes, etc.

7: Hollow, tempered, frosted, flat, heat absorbing, reflecting, interlayer, wire clamping, embossed glass, etc.

8. Whether the inner and outer frames between the window frame and the wall are neutral silicone sealants.

9: Check the screen window.

10: balcony, bay window guardrail height, vertical pole spacing, guardrail installation and fixation, etc. Protective measures should be taken when the window sill is less than 0.9M.

1 1: Check whether all doors and windows are installed firmly and whether the door leaves and sashes are skewed.

12: Check whether all doors and windows are pushed and pulled smoothly.

13: Check whether all door and window locks are flexible, firm, easy to operate and evenly locked.

14: Check whether all doors and windows are beyond the allowable deviation range of installation.

15: Check the dropper.

Fourth, civil engineering.

1: The walls, floors and ceilings are all empty.

2; Using infrared projector to detect roof flatness.

3. Infrared rangefinder detects the clear height of the house.

4. Check whether the angles of Yin and Yang in all rooms are straight and square.

5: Whether there are cracks in the wall, floor and ceiling.

6: Whether there are rust spots on walls, floors and ceilings.

7. The strength of plastering cement mortar.

8: Whether the coating is powdering.

9: Check the 90-degree angle of all rooms.

10: wall flatness inspection.

1 1: Check the verticality of the wall.

12: strength of cement mortar for ground leveling layer.

13: Check the external wall insulation.

14: Check the beam deflection

15: whether the reinforcement is exposed, whether the wall surface leaks, whether there are cracks in the wall, and whether the load-bearing walls, beams and columns meet the design specifications.

16: Check whether the width and height of the doorway meet the standards.

Five, water supply and drainage engineering

1: Test the water pressure with a hydraulic press.

2; Check the water meter (assist the owner to read the meter).

4: Check whether all water outlets are sunken or skewed.

6: Check for leaks.

7: Check the water supply pipe.

8: Check the drain pipe.

9: Check the bathroom waterproof.

10: Check the backflow gradient of the drain pipe.

1 1: Check whether the floor drain and toilet water are blocked.

12: Do the toilet closed water test.

13: Check whether the installation slope of the drainage pipe is even, and there can be no reverse slope.

14: Check whether the manhole settings of the vertical pipe, branch pipe and horizontal pipe of the drainage pipe are standardized. ,

15: Check whether the floor drain is set with "S" bend.

16: Whether the balcony has drainage measures.

17: floor drain inspection.

Six, strong and weak electricity engineering

1: Check whether the wire diameter is up to standard.

2. Check whether the installation of distribution box is smooth, firm and standard.

3. Check whether the wiring in the distribution box is neat, whether there is splicing phenomenon, whether the loop number is complete and whether the identification is correct.

4. Check whether the models and specifications of electrical appliances and wires in the distribution box meet the design requirements, and leave enough terminal board, wires and wiring space.

5: Check whether the PE line of the distribution box is connected with the box.

6. Check the water and electricity diagram to see if the construction is carried out according to the diagram.

7: Test all sockets with phase detector.

8: Check the equipotential connection in the bathroom.

9: Check the leakage protection of the distribution box.

10: Lasong line.

1 1: Check whether all switch panels are flexible.

12: Open all sockets and check whether the wiring and construction are standard.

13: Check whether the cassette is damaged, protruding from the wall and locked.

14: test lighting.

15: View the multimedia information box.

16: Check the electric meter (assist the owner to read the meter).

17: Whether the size of the electric energy meter meets (10-40A).

Seven, air conditioning exhaust device

1: Check external positions such as air conditioners and drain pipes.

2. Check whether the air conditioning through hole is high inside and low outside, and whether it is embedded in advance.

3: Whether the kitchen flue is equipped with a fire check valve.

4; Test whether the kitchen flue is unobstructed.

5: check cigarettes.

6: Smoke exhaust, exhaust pipe, fittings, smoothness, nozzle setting, etc.

7: Check the infrared curtain.

Eight, heating engineering, gas

1: Check the gas meter.

2. Check the radiator.

3: Check the radiator for rust, water leakage, cutting, paint peeling and installation skew.

4: Pipeline, leakage, radiator, pipeline, valve, bracket and equipment, anticorrosion and painting.

5. Gas alarm, components, installation, pipeline arrangement and safety valve.

6: Check the gas sleeve.

Nine. others

1: Check the visual intercom.

2. Measure the usable area of the house.

3. Measure the building area inside the house.

4. Check whether the fire control facilities are perfect.

5. Check whether the elevator is qualified (inspection mark).

6. Whether the width and steps of stairs meet the requirements.

7: Barrier-free access.

8. Whether the small high-rise stairwell is equipped with fire emergency lights.

9: Whether the unit visual intercom door is installed.

10: roads, greening.

1 1: whether the bar is off-welded, missing welded or virtual welded.

12: Whether the opening direction of the stairwell fire door meets the requirements.

13: Check the clear height and clear height of corridors and public passages.