What if the angle valve in the wall is broken?

Question 1: What should I do if the angle valve in the wall is broken? ! Take it out like this. If you don't use the saw too slowly, you will break the screw, too. Fix it with hexagon screws first. Connect the screwdriver when you are free. It's not loose. As soon as you turn it, the angle valve gets stuck in it for one minute.

Problem 2: The angle valve on the wall is damaged. Patent 1. Replace the indoor faucet, triangle valve, water inlet and outlet pipes and water meters. 2. Replace the air switch, leakage protector, indoor switch and socket panel. 3. Replace bulbs, fluorescent lamps, annular tubes, ballasts, fuses and electric meters. 4. Check and replace the water pipes and circuits in the lamp. 5. Replace the washbasin, sink, toilet cover and water tank fittings. Troubleshooting of lines, replacement of lamps, sanitary ware, electric fan, water heater and washstand, installation of lampblack machine lamps, and installation of strong current and weak current (telephone lines, closed lines, network lines, etc.). ) water pipe wiring, plugging, water pump replacement, water tower leakage maintenance, drainage pipes, faucets, triangle valve, valves, water inlet and outlet hoses and water meters.

Question 3: The angle valve is broken on the wall. What should I do if I can't take it out and seal the hole? This is a common problem for plumbers. It's very troublesome and delicate, and it needs patience. First, put the hacksaw bar into the damaged nozzle, and slowly cut several notches with proper depth on the inner wall (not too deep, or it will hurt the internal thread), and then dig out the remaining parts of the divided faucet bit by bit with a chisel. The cheap angle valve your mother bought is made of alloy. Over time, it will become brittle and easy to be removed. Be patient.

Question 4: Angle valve is twisted in the wall. Hurry up! Turn off the water, find the property, pay the money, open the wall and take over again. The worst thing is to solve it like this.

Question 5: What should I do if the copper angle valve breaks the wall? Look at the cross section. It should be uneven. Find a screwdriver and knock it out in the opposite direction. If the cross section is relatively flat, find a hacksaw, slowly cut a hole in it, and then knock it out with a screwdriver. Remember to type it in the opposite direction.

Question 6: What should I do if the wire in the angle valve is broken at the elbow? Now I can only be a dead horse as a living horse doctor. (1) Dry the water stain, spray some rust remover, hold the broken inner wire with a solid object, knock the solid object properly, then insert the (tightened) inner wire with a board file of appropriate size, and pull the board file with a wrench to drive the inner wire to exit. (2) Go to the hardware market to buy English foreign silk before attacking. You can use a smaller one first. (3) Use a hacksaw to cut the inside wire into three sections from the inside out, and the sawing depth shall not exceed the thickness of the inside wire, and then use a chisel to chisel it out. (4) Reaming the hole with a round file, and then tapping the wire with an outer wire. When sawing or filing, pay attention to slight back and forth movement, and don't chisel nonmetallic elbows. Give it a try!

Question 7: The angle valve in the wall is broken. What if the inside line is not clean? Do you have any special tools? If the copper angle valve is used, it can last for 5-8 years at worst. If it only takes about three years. Then it should be a zinc alloy angle valve. As long as it's not too difficult to bargain these days. General stores will not sell zinc alloy angle valves to customers. . . If the zinc alloy angle valve is broken. Ha ha. It's big.

Question 8: The corner valve in the wall is broken ~ Call for help. This is a common problem for plumbers. This is a troublesome and delicate job, which requires patient operation.

First, put the hacksaw bar into the damaged nozzle, and slowly cut several notches with proper depth on the inner wall (not too deep, or it will hurt the internal thread), and then dig out the remaining parts of the divided faucet bit by bit with a chisel.

The cheap angle valve your mother bought is made of alloy. Over time, it will become brittle and easy to be removed. Be patient.

Question 9: What should I do if the faucet or angle valve on the wall is broken? Use an angular object of appropriate size, such as a faucet broken by a triangular scraper or a corner valve hole, to forcibly rotate counterclockwise.