Daily use of movable partition

First, how to open the multi-directional screen

All operations should be gentle and safe. Stand facing the screen, grab both sides of the screen with both hands, and gently pull the screen along the track; Then rotate the screen along the track.

After pushing the screen to a suitable position, fix the screen. Tip: When pushing the screen to the intersection, pay attention to the direction of the track, and then gently push the screen into place along the track.

Second, how to fix the multi-directional screen?

Hold the screen with one hand, and insert the handle into the hexagonal angle steel at the vertical position 1 100MM on the side of the screen with the other hand (as shown in Figure 3). Grasp the handle and rotate it clockwise 180 degrees (or shake it continuously). The telescopic seal inside the screen pops up to fix the screen.

Insert the handle into the groove on the side of the screen, pull the handle upward, open the telescopic seal inside the screen and fix the screen. After the whole screen is put in place, see if the screen is straight? Whether it is in the same plane with the track, if it is not straight, retract the upper and lower telescopic seals for adjustment until the screen is straight.

Third, how to operate the multi-directional telescopic screen?

Usually the last side of each group of screens is a retractable screen. Push the screen to the place where it should be placed, then pull the handle upward in the vertical groove on the side to pop up the upper and lower movable seals (as shown in figure 1), then put the handle into the operation hole on the surface of the retractable screen (as shown in figure 2) and rotate it counterclockwise until the retractable aluminum plate on the side presses against the wall.

Fourth, how to operate the door of the multi-directional screen? Push the door where it should be placed and touch the front screen, insert the handle into the groove on the side of the screen (as shown in Figure 4), pull the handle upward, open the telescopic seal on the inside of the screen and fix the screen. Open the small door, insert the handle into the operating hole of the leg on the other side of the screen (as shown in Figure 5), pull the handle upward, open the telescopic seal on the other side of the screen and fix the screen.

Five, how to turn off the multi-directional screen

1. If there is a middle door, first press the square holes on both sides of the middle door to rotate 180 degrees, loosen the upper and lower seals through the driving wheel, and then close the middle door;

2. Open the upper and lower seals of the telescopic aluminum plate and the last filter screen;

3. Retract the telescopic aluminum plate of the last screen to make it produce at least the distance that can rotate the screen, which is generally about140mm; 4. Gently push the screen to the closed position along the guide rail;

5. After placing each group of screens in the same way, press once every two screens to minimize the distance between the screens. If necessary, the upper and lower movable seals of the last screen collected at the hidden board can be opened to make it close to the track and the ground, which can prevent others from pulling out the screen casually. Tracking system:

1. As shown in the figure, before installing the partition, check the track assembled by track components in turn on the floor.

2. Mark the track line and place the bracket in a specific position.

3. Install the rail bracket to the ceiling.

4. Check whether the movable partition wall is firmly fixed on the track. When the rails and brackets must be stored loosely in the storage area, so that the bracket plates can be moved to other places.

5. Finally, before adjusting the facilities of the main track, measure the proper position of the storage track. This is very important for the placement of intersections.

Installation of track facilities:

1. When the partition is hung on the track, the escape track can be removed without rebuilding the crane.

2. For the escape exit track, it must be a special bracket track connection.

3. When installing the track, the construction shall be carried out according to the accurate data adjusted during the measurement.

Track adjustment:

1. Please remember that all the rails above the brackets are loose enough. Ensure the track pause time.

2. Tighten all track connections and adjust the horizontal height of the track correctly. The track installation direction must also be horizontal and straight.

3. When installing track facilities, sound insulation and mineral wool are necessary plates for installation.

4. The track has "L", "T" and "X" joints, which are used for turning connection and can be divided into "L", "T" and "right". Generally, it is not recommended to use the word "ten" to refute. L and t are trimmed to corresponding sizes, and their positions are indicated by numerical marks.

Feasible wallboard:

1. Open the escape route;

2. According to the tracking system, remember to fix it on the track in the correct order.

3. Before closing the movable partition, adjust the height of the carrier and check the right angle of the track so that the track partition can run well.

4. Check the verticality of all partitions. If they are not damaged, they can enter the edge of the aluminum frame of the rubber seal vertically without bending (if the connection is inappropriate, otherwise).

5. If the track direction is horizontal, but the partition is suspended and inclined, the height of the vehicle must be adjusted.

6 clockwise = partition rising, left turn = partition sinking;

7. Remember that height is good. Tighten the socket for inserting the carrier, adjust the partition and open it when the track is full, and adjust the width of the door shape. 1, manufacturer qualification. Including the company's establishment time, technical force allocation, company production scale, etc.

2. Project situation. The more projects the manufacturer has, the more secure the technology will be. See if the factory has formed a perfect product system, such as guaranteed quality and mature movable partition technology.

3. After-sales service guarantee. After-sales service commitment, including service terms, wearing parts and consumable parts. Relatively speaking, the company has been operating for many years and participated in large-scale project companies, so the service is more secure.

4. Material situation. Only when the materials are guaranteed can the company have quality assurance.

5. Provide relevant test reports. The manufacturer is required to provide the fire-fighting test report issued by the national fire-fighting agency, the sound insulation test report issued by the nationally recognized acoustics research institute, and the load-bearing test report of the guide rail and pulley.

How to choose the movable partition will be more upscale?

How to choose the movable partition will be more upscale? Here are several ways, let's have a look.

1, there are many kinds of movable partition materials, glass, metal, cloth, bamboo and wood are all optional materials, and some relatively movable partition screens, such as streamline beads, are the best partitions for small rooms.

2. If the partition is moved to the top, it is necessary to change the smoke and spray, and the property management company usually requires the owner or decoration company to solve it by itself.

3. Many wires and sockets should be connected by partitions, and the appearance should be shaped. Because the movable partition itself is relatively heavy, as long as there is a track, it can become load-free, so it can be applied to any shape in design, and the change of length and reality can also be arbitrary, and there is a lot of room for free play. 1. Generally, movable partition screens have a variety of finishes, including hard boards and soft boards. Hard board refers to the movable partition screen made of melamine and other plates. The cleaning of this movable partition screen can usually be solved by simple scrubbing. 2. We can also clean the movable partition veneer of rattan with salt water or a little vinegar, or neutralize it with detergent, which can effectively prevent discoloration and decoloration, and can well remove stubborn stains. 3, soft partition material is soft bag, leather, cloth, this kind of movable partition cleaning is not so simple and easy, we need to clean it slowly, you can use some detergent or salt water without preservatives to clean it, because this can not only be very good decontamination, but also keep the veneer very elastic and shiny. If there is no preservative-free detergent, then we should not use it more, because it will destroy the partition.