Job Recruitment Website - Recruitment portal - Introduction of installation method and matters needing attention of electric shutter door
Introduction of installation method and matters needing attention of electric shutter door
Brief introduction of electric shutter door
The electric shutter door is connected in series with the multi-joint movable door piece, and the start is driven by the motor group. The shutter door rotates the upper and lower doors around the scroll above the door in the fixed slideway. Suitable for commercial facades, garages, shopping malls, hospitals, factories and mines and other public places or houses. Especially in the place where the door opening is large and it is not convenient to install the ground door body, it plays a convenient and quick opening role. Such as garage doors, fire shutter doors in shopping malls and airplane garage doors.
Installation method of electric shutter door
First, draw a line where the door frame needs to be installed. Indicate the size, and then ask the master to design a suitable electric shutter door. It is worth noting that the height inside the frame is a little higher than that of the door leaf.
Second, fix the door frame of the electric shutter door first. Here, the fixing plate at the lower part of the door frame should be removed first.
Note: grooves should be reserved on the ground on both sides of the hole. After the calibration is qualified, the wooden wedge is fixed, and the iron foot of the door frame is welded firmly with the embedded iron plate. With cement mortar or strength not less than 10MPa? Fine stone concrete can be firmly blocked.
Third, install the main door leaf of the electric rolling shutter door. Make sure that the electric shutter door and the wall are integrated and sealed, and then paint the hole and the wall. After painting, the gap of the door should be even and smooth, and the electric shutter door should be opened freely and lightly, without being too tight, too loose and rebounding.
Matters needing attention in installation of electric shutter door
1, check whether the hole is consistent with the product size, and the size of the hole of fire shutter door can be calculated as 3M.
2. Determine the installation horizontal line and vertical line, and install them in turn according to the set size. The notch size should be accurate, consistent from top to bottom, and the corresponding notches should be in the same plane, and then the embedded parts should be welded in the hole with connectors.
3, door rolling machine must be installed according to the requirements of the manual.
4, scroll, frame plate must be firmly installed on the concrete structure or embedded parts.
5. A central pillar should be installed in the middle of the wide door body, with slideways on both sides. The center pillar must be installed perpendicular to the ground. Straight, firmly installed, but easy to disassemble.
Electric shutter doors are increasingly favored by people. Electric shutter doors are loved and bought by consumers because of their convenience and no space occupation. Widely used in commercial facades, garages, shopping malls and other public places, especially in places where the door opening is large and it is not convenient to install the ground door. It is suggested that you carefully understand the relevant information before purchasing and using it, so as to give full play to its role in purchasing and using and prolong the service life of electric rolling shutter doors. The above information is shared with you, and I hope it will help you.
Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp; Wb, you can get it for free ~
- Previous article:What do you learn in technical schools?
- Next article:What is the written recruitment test of Sichuan Mobile Campus?
- Related articles
- Shagang group. How much is a2 driver's salary?
- Is the car loan paid for overseas inspection and recruitment?
- How about working in Zhaopin Recruitment Company?
- Which decoration in Tengzhou is reliable and cheap?
- Is Tangshan Nanhu Park free?
- What software outsourcing companies are there in Hangzhou?
- How do flexible employees in Taizhou participate in medical insurance?
- I want to take 10K in the interview. HR says you are only worth 7K. How to answer or refute?
- How many kilometers is it from Jiaozuo to Yanghe and how to get there?
- Admission requirements of Changshu Shihua International School