How to design CDR recruitment posters?

Many times, creative recruitment posters can not only reflect the unique taste and connotation of employers, but also attract the attention of job seekers. And how to make an attractive company recruitment poster? In fact, it can be easily satisfied with CorelDRAW software! What I will share with you below is the CDR recruitment poster design tutorial! Let's take a look ~CDR recruitment poster design tutorial: 1, new document. This page is A4 size. Vertical page. Other defaults will do. Of course. 2. Click the Bezier tool to draw a shape, and then press the C key to change the direction of the control line. As shown in the figure. Press F 10 to adjust with the shape tool. Use the Node tool in the property bar to adjust the point. 3. Click the selection tool, double-click the graph, and then place the center point, as shown. Click the menu bar to transform and rotate the object, and enter a 45 angle in the pop-up menu; Copy 7 Click Apply. As shown in the figure. 4, color filling, two petals and one color. Fill in: ①#A 1CB76 light green ②#A9CB05 grass green ③#028A44 dark green ④ # 61b 431; Select all, right-click xx, and remove the outline color. 5. Use the transparency tool and select Uniform Transparency in the property bar. The pattern is decreasing. The effect is shown in the figure. 6. copy a layer of ctrl+c; Ctrl+V. Then group ctrl+g, fill the upper right layer with white, and remove the internal filling. As shown in the figure. 7. In the tool selection mode, double-click the bottom layer and drag it with the double arrow in the upper right corner until it rotates correctly. Make it smaller. Click Transparency to change the transparency of the upper layer to none. And routine. As shown in the figure. So the white line came out. Press F 12 to select and check the confirmation of object scaling. 8. Hold down the ctrl key and draw a perfect circle. Fill it with white, press and hold the shift key to copy one, shrink it, then select two circles and select the trim of the property bar. Fill the trimmed outer ring with # 55ad3c; As shown in the figure. 9. Remove the outline. Select the transparency tool and select the uniform transparency reduction effect of the property bar as shown in the figure. 10, select the middle circle, remove the outline color, copy the plus key of the keypad and fill the green # 62b532 layer by layer, then select the transparency tool property bar, select gradient transparency, and edit the transparency inversion effect of general elliptical gradient transparency as shown in the figure. 1 1. Then click the transparency tool and click the middle circle. When two transparent blocks appear, we will add another one, with black representing transparency and white representing opacity. Add a black block at the position shown in the figure (drag the black block from the color bar to the position where you want to place it). The effect is shown in the figure. Note that click on the black color block in the middle, as long as it is at100; Then box all, ctrl+g group. 12. Select the rectangle tool to make the background color, then select the ellipse tool, press ctrl to draw a perfect circle, fill it with white, and remove the outline. Add an elliptical gradient and select the brightness of the property bar; Make a copy and make it smaller. As shown in the figure; 13. Select these two and select the adjustment tool. From the left picture to the right picture. As shown in the figure. Then make a copy. Draw a curve at will with Bessel tool, draw it with C key, and then adjust it with shape tool. Select the coordinated drawing and click the property bar to change the step size to 50. Click the new path. When the arrow appears, click the path. In the property bar, click Coordinate and Rotate All Objects along the Whole Path to make a selection. The effect is shown in the figure. Select the path, right-click to split the mixture on the path group, then click the path and press the delete key to delete. The effect is shown in the figure. Draw a curve at will with Bessel tool, draw it with C key, and then adjust it with shape tool. Select the reconciled graph, click the property bar, and change the step size to 80; Click the new path. When the arrow appears, click the path. Click in the property bar and coordinate and select along the entire path. The effect is shown in the figure. 14. Draw curves at will with Bessel tool, draw with C key, and then adjust with shape tool. 15, select the reconciled graph, and click the property bar to change the step size to 50; Click the new path. When the arrow appears, click the path. In the property bar, click Coordinate and Rotate All Objects along the Whole Path to make a selection. The effect is shown in the figure. 16. Select the path, right-click to split the mixture on the path group, then click the path and press the delete key to delete. The effect is shown in the figure. 17. Draw curves at will with Bessel tool, draw with C key, and then adjust with shape tool. 18, select the reconciled graph, and click the property bar to change the step size to 80; Click the new path. When the arrow appears, click the path. Click in the property bar and coordinate and select along the entire path. The effect is shown in the figure. Select the path, right-click to split the mixture on the path group, then click the path and press the delete key to delete. The effect is shown in the figure. If you think the effect is not good, you can do it again. Until you are satisfied. Box selection, group ctrl+g; 19. Select the complex star tool and enter 10 edge in the property bar, with sharpness of 3 and no outline; Make a copy. 20. Select the deformation tool, and select zipper deformation in the property bar; Zipper amplitude100; The effect is shown in the figure. On the other hand, select the click deformation tool and select the push-pull deformation push-pull amplitude value in the property bar: 200; 2 1. Select three figures, press C and E keys on the keyboard, align them in the center, select a little star and rotate it 90 degrees. Hold down the shift key and zoom in. Select the circle and enlarge it. As shown in the figure. Select these three groups. Make a copy and put it in the right place. 22. Draw a circle and fill it with #D6E59A. The ellipse is transparent. As shown in the figure. Remove the outline. Copy multiple copies and put them on the page, and change the size as shown in the figure. 23. Draw a rectangle, fill it with #7 1B83B green, and remove the outline. Add a uniform transparency of 68. Copy a layer. (Left-click drag, right-click copy) and change the height, and fill the upper layer with #FFF582 light yellow. ) In the tool selection mode, rotate 29. Select these two layers and make a copy, and place them as shown. Change the transparency to 8224, drag the flowers a little bigger and put them on the upper layer. You can press ctrl+pageup; Then input text, the font is: Founder, Bold, Black, Simplified; Copy a layer of flowers. Fill the text with #A3D386 light green; Press F 12 to modify the outline width of 2.5mm and the color # 89C46525. Copy the text layer by layer, press F 12 to modify the outline width of 2.5mm and the color # ffffff to change the text color to # 75ba2226. Copy several small ones and put them in different positions. As shown in the figure. And enter the text. Copy multiple asterisks onto the page. 27. Draw a rectangle at the bottom. Fill # 78ba25 Copy a layer to the top and adjust it with the shape tool, as shown. Convert the rectangle above into a curve and adjust the deletion point with the shape tool. Form a triangle. As shown in the figure.