Job Description of Bed Cutting Supervisor Job Responsibilities of Bed Cutting Staff

Job responsibilities of the employees of AoLiXing Cutting Machine

Objective: In order to do a good job of cutting machine and cooperate with the normal operation of the company's assembly line production, the job responsibilities of all employees of cutting machine are listed.

first, the general rules

1. The lathe cutting staff should seriously abide by the company's factory rules and regulations and be a civilized and polite worker.

2. The lathe workers must safeguard the interests of the factory, establish the code of conduct of "serving the next working procedure" and "the interests of the company

first", and make concerted efforts, mutual cooperation and sincere cooperation to do the first step of the factory operation.

3. The lathe cutting staff must seriously obey the arrangement of the lathe cutting supervisor and complete all

instructions and tasks issued by the supervisor.

4. Before production, the lathe cutting staff should carefully understand the production instructions, and carefully fill in various detailed

tables and related statements to avoid mistakes.

2. Responsibilities of employees in each department

1. Responsibilities of cloth puller

1) Before cloth pulling, the cloth should be loosened 24 hours before it is fully recovered, and special cloth should be handled according to temporary regulations; 2 yuan will be detained every time those who fail to comply with the regulations.

2) Be sure to distinguish the front and back of the cloth before pulling it; One-time buckle for pulling the reverse side 2-2 yuan

3) When pulling the cloth, cancel the salad cloth and use monochrome cloth paper. Must be relaxed and smooth, not wrinkled; The loss of a Blab is controlled within 5CM, and the 1 yuan is deducted every 2.5CM if it exceeds 5 cm, and the thickness of the cloth is controlled within 15CM; 1 yuan will be detained every time those who fail to comply with the regulations.

4) The quantity of cloth to be pulled shall strictly comply with the production instructions, and the cloth to be pulled shall be 1% in conformity with the approved color card, and Buffon and Booker shall be in conformity with the preparation list. If any abnormality is found, the cloth to be pulled shall be stopped immediately, and the superior (supervisor, merchandiser, quality department and production department) shall be asked to handle it.

5) When pulling each bed of cloth, you must clearly fill in the relevant information such as the number of pounds of cloth, cylinder number, how many pieces of cloth are pulled, how many pieces of cloth are left over,

mark frame distribution, payment number, etc. After pulling, you must check the front and back of each compartment to make sure that it is correct before you can make a cutting order. If there is an error in the number of cuts

, each cut will be deducted by 2

6). Each cut must be checked according to the level specified in the drawing table. If it is found that the level of less pull and more pull should be immediately reflected to the superior, the cutting will not be allowed until it is handled. Otherwise, 5 yuan will be deducted every time, and 1 yuan will be deducted the most if the result is serious.

7) In case of local defects, breakage, oil stains, etc., the cloth should be spliced or marked obviously. If it is found that it is cut without any marking, each piece will be 1 yuan-treated. Serious

defects, breakage and oil stains are forbidden to be used as bad cloth, and immediately ask the superior for treatment.

8) The film changing cloth should be color-separated, bundled with cylinder number and paragraph number, clearly marked and sent to the cutting machine for later film matching.

2. Job responsibilities of electric shears

1) Before cutting, recheck the mark frame, check the pattern in detail, and then sign it with the supervisor before cutting; 2 yuan will be deducted every time the work is started without approval, and 2 yuan will be deducted for the most serious cases < P >.

2) The cutting sequence is from small to large and from difficult to easy. When cutting the circular position (collar, sleeve top, washing mark position, etc.), the cut must be made in the middle position, and the knife note should be clear < P > and should not exceed the depth of 1 minute. Every time you don't make a cut, you buckle 2 yuan.

3) After cutting, the cut pieces should be folded up and down, left and right for inspection in time, and every piece of the cut pieces found deformed in the workshop should be 1 yuan; You cannot use the

maximum deduction 5 yuan that needs to be re-allocated.

4) The electric clipper should refuel and maintain the electric clipper regularly. Man-made damage maximum deduction 2 yuan. 3, numbering job responsibilities

1) All cut pieces are numbered from the reverse side in sequence,

2) The handwriting typed by the numbering machine must be clear (if there is an ambiguous deduction of 2 yuan

).

3) When weaving light-colored pieces, you must not use dark ink to number them, but use a silver pen or a water-soluble pen to number them. (One-time deduction for dark ink number is found. 5-2 yuan

4) The number of the whole bed should be clear, and there should be no sign-jumping and no sign-jumping. (If there is a sign-jumping and no sign-jumping, one-time deduction will be made. 2-1 yuan

4. Responsibilities of binding post

1) First, all parts of the cutting piece (main cutting piece and all small parts) should be divided into sizes. The bales must be signed off.

If the bales are wrong, 5 yuan will be deducted for each bale.

2) The cut pieces and all the small parts must be bound tightly with the same color cloth strips or light color cloth strips.

The surface cloth is folded inward for binding. Bundled cut pieces shall be placed in order according to the designated position, with sub-payment,

color separation and code division. 1 yuan will be deducted every time there are pieces cut off or

pieces omitted.

3. Other work

1) When picking up the cloth, the supervisor must fill in the form and the material requisition form approved by the production department. When picking up the cloth, check whether the color and weight of the cloth are consistent with the documents, and return the rest of the cloth to the warehouse when it is

, otherwise, 1 yuan will be deducted every time, and 5 yuan will be deducted at the highest level in severe cases.

2) The receiving personnel (sewing transceiver, sewing team leader or supervisor) must be required to make a clear inventory of the cut pieces sent to the sewing machine, and everything should be consistent with the delivery note and card flying, so that the delivery is clear

, and the receiver signs for recognition, otherwise 1 yuan will be detained every time.

aolixing clothing co., ltd. 211-3-11