Job Recruitment Website - Zhaopincom - Only responsible for construction, wallpaper to make money?

Only responsible for construction, wallpaper to make money?

Make money by wallpaper! Stay 1 month or more, and each person can earn 5000 yuan. Learn to paste wallpaper from the wallpaper master first, and then go to various wallpaper shops to choose wallpaper stickers. Opening a wallpaper shop has a bright future! Paste method of wallpaper 1. The tools and materials used in the general pasting method of wallpaper are: glue, gypsum powder, brush, towel, sponge, sandpaper, cutter, scraper, tape measure, barycenter hammer, glue container, etc. (1) The basic procedure for posting is: 1. Wall treatment: scrape off impurities and floating soil on the wall with a scraper, and smooth the cracks in the concave holes with gypsum powder. If the wall is soft or has a powder layer, it should be coated with wallpaper glue first to make the wall firm and the wallpaper will not fall off. 2. Cut the wallpaper: measure the height of the wall first, and then cut the length of the wallpaper. There are two situations: don't cut the floral wallpaper according to the height of the wall, the length is about 10 cm, which is used for upper and lower trimming; For floral wallpaper, the symmetry of the pattern should be considered, so the cutting length should be increased according to the actual situation, usually longer than 10 cm. 3. Glue coating: Brush the wallpaper glue on the back of the cut wallpaper with a brush, paying special attention to the surrounding edges to ensure the construction quality. Leave the wallpaper coated with glue for 5- 10 minutes (be careful not to apply external force to avoid creases in the wallpaper), so that the glue can completely penetrate into the bottom of the paper before pasting. Brush several wallpapers at a time and stick them in order. 4. Wallpaper construction: measure the vertical foundation line with the center of gravity hammer, stick the first wallpaper from top to bottom according to the foundation line, scrape the wallpaper gently from top to bottom and from inside to outside with a scraper, and squeeze out bubbles and excess glue to make the wallpaper flat and close to the wall. 5. Trimming and cleaning: cut off the redundant wallpaper at the upper and lower ends, and the blade should be sharp to avoid burrs. You'd better use a new scalpel when cutting some wallpaper. Wipe the glue left on the surface of the wallpaper thoroughly with a sponge to prevent the wallpaper from turning yellow. After the wallpaper is dried, if bubbles are found on the surface, cut it with a knife, inject glue and flatten it to eliminate it. (2) Matters needing attention in construction: 1. Check carefully whether the color number and batch number of wallpaper are consistent before construction. Also know the type of wallpaper to be constructed, color paper should be aligned, and plain paper should be constructed in positive and negative directions. 2. The quality of glue will directly affect the overall effect and service life of wallpaper, so you need to buy genuine brand glue or wall powder. 3. In some damp and backlit houses, there is sometimes a layer of mold on the wall, so it is best to clean it with disinfectant. 4. Dry mounting, that is, the construction method of coating glue water directly on the back of wallpaper, mainly for pasted wallpaper. Wallpapers with cross cloth and non-woven bottom do not need to be pasted. 5. The wallpaper with glue on the back should not be completely involved in the water to avoid adhesion. 6. The consistency of glue is judged by whether a chopstick can stand in the glue. 7. In case of internal angle, gravity hammer construction shall be started from the internal angle of the house 10 cm away. In order to avoid deviation. 8. Patterned wallpaper, starting from the center of the wall at eye level, usually aims at the repeated patterns at the junction of two trimming edges. 9. During the construction of pure paper wallpaper, it is not allowed to scrape the paper glue hard to avoid polluting the wallpaper surface. 10. If quality problems are found during construction, the construction personnel shall be required to stop construction immediately. To be solved by the dealer. 1 1. Don't throw away the scattered wallpaper for future repair. 12. After pasting the wallpaper, open the doors and windows to keep the room ventilated. 13. When you need to hang oil paintings or other decorations on the wall, you should draw a V shape on the nail wallpaper for later repair. (3) The construction method of wall covering is basically the same as that of ordinary wallpaper. Note: 1. Because wall covering itself absorbs water, it is necessary to add a proper amount of white glue to the glue to increase the adhesion. 2. Do not use a hard scraper, but use a soft brush to avoid damaging the fabric surface. 3. If the glue overflows, suck it off with a sponge to avoid damaging the cloth surface. (4) The basic construction method of tin foil (metal) wallpaper is the same as general wallpaper. Note: 1, wall treatment must be clean, dry and flat. Because any convex and concave condition of the wall is easy to appear after pasting metal wallpaper. 2. Some wallpaper has been trimmed, while the textile wallpaper with metallic texture may need to be trimmed on the wall. Suitable for 24 inches (60.9 cm) wide metal wallpaper. Cut at least 0.6cm on both sides. 30-inch (76.2 cm) wide patterned metal wallpaper can be cut along the inner side printed with trimming marks. If it is a landscape wallpaper, be sure to determine the posting order of the patterns before pruning. 3. Glue must be evenly coated on the wall, and it must not be directly coated on the metal wallpaper. Each time, the glue is only applied within the range of the single sheet of paper to be pasted. 4. Stick it with a soft brush. Because the metal wallpaper will not expand and contract, it is necessary to squeeze out bubbles at any time. 5. To keep the surface of the wallpaper clean, clean up the excess glue overflowing from the seams and surfaces at any time, and change the cleaning water frequently. 6. Pay attention to the fact that a layer of gold foil or tin foil on the surface of the metal wallpaper will also conduct electricity, and pay special attention to avoid live lines such as power supplies and switches. (5) Sticking method of power switch and socket 1. Turn off the main power supply before construction to avoid electric shock. 2. Cover the wallpaper on the whole power switch or socket, cut two diagonal lines from the center point, and four small triangles will appear, and then cut off the redundant wallpaper along the power switch or socket with a utility knife. Wipe off the excess adhesive with a rag. (6) Decorative strips with decorative strips are usually used with wallpaper colors because of their elegant pattern design and beautiful colors, and can also be used alone with painted walls. The purpose is to enhance the effect and atmosphere of interior decoration with the help of elegant patterns and colors of decorative strips. Decorative strips in advanced countries in Europe and America have become a necessity for interior decoration and are widely used in various places, such as homes, commercial buildings and entertainment spaces. , indoor walls, ceilings can be seen everywhere, waist line, corner, wall top, or the beautification of various border edges, such as window frames, door frames, light frames, book frames, etc. , can be used instead of or in conjunction with the traditional wire frame, and the effect is very good. If decorative strips can be used creatively and boldly, it will make the finishing touch to the whole room.

Calculation method of wallpaper consumption

1。 Know the calculation method of wall length, width and height:

{(length+width) times 2 times height-door and window area (note: door and window area times width)} divided by 4.5 (note: the area of a roll of wallpaper is 4.5 square meters (10m)), the number obtained is the required number of rolls.

2。 I only know the square number of rooms: the square number of rooms multiplied by 3.3 (note: multiplying 3.3 is a formula of buildings, doors and windows have been removed) divided by 4.5, and the number obtained is the number of rolls needed.