A must-learn for moms of baby girls! Super cute baby hair decoration DIY

A must-learn for moms of baby girls! Super Cute Baby Hair Accessories DIY Moms with daughters must be no strangers to cute hair accessories! But a baby's hair accessories sometimes cost nearly a hundred dollars. How can a smart mother help her baby dress up stylishly while keeping her wallet in mind? In this issue, follow the creative handiwork of Apple Mommy and help your little baby make different styles of dazzling hair accessories! Materials for small flower hairpin:

1 dot cloth (width 30cm long 6cm), 1 ribbon (width 1 length 15cm), 1 cloth buckle, 1 ladybug, 1 H hairpin (6cm long), hot melt glue (if there is no hot melt glue, Styrofoam glue can be used instead) Steps:

1. Draw 5 circles with a diameter of 4cm (1cm apart) on the cloth, and cut them out along the circle line leaving a 0.5cm seam allowance.

2. Paste double-sided tape on the back of the ribbon to cover the entire H hair clip, and bake the tail of the ribbon over a low fire to avoid stripping, which is the satin-wrapped hair clip.

3. Condensate the seam along the circle line and stuff the cotton. Tighten the thread and tie it into a knot. After completing 5 pieces, connect them into a circle and tie them to form a small flower.

4． Attach the florets from step 3 to the hairpin with hot melt glue, and attach a cloth button and a small ladybug in the middle of the floret.

A must-learn for moms of baby girls! Super cute baby hair decoration DIY crown headband materials:

Hollow-shaped sequins (height 6cm wide 12cm), round non-woven fabric (diameter 3cm, 4cm) each 1 piece, 1 yarn (width 10cm long 80cm) , 1 bead string (12cm), 1 decorative bow, 1 satin-wrapped headband. Steps:

1. Glue the head and tail of the modeling sequins into a circle, and glue a 4cm diameter round non-woven fabric on the bottom to form a three-dimensional crown.

2. Along the bottom of the crown, apply a little hot melt glue to the beads to form a circle and secure them at the head and tail joints.

3. Fold the yarn in half up and down to a width of 5cm, use a needle thread to shrink the folded part, connect the head and tail in a circle, and tie it tightly to form a wavy round yarn.

4． The bottom of the crown is fixed on the round yarn with hot glue, the bow is glued to the end of the bead string, the bottom of the round yarn is glued to the non-woven fabric and then glued to the side of the headband. TIPS: Hairband wrapping method

Paste 1cm wide double-sided tape on the upper and lower sides of the toothless hairband, then tear off the upper and lower sides of the tape at the front end, take a 1cm wide satin ribbon and wrap it at an angle to the end. Then wrap the black finishing tape 2 times around the head and tail ends to strengthen the fixation. A must-learn for moms of baby girls! Super cute baby hair accessories DIY lace lady hat hairpin materials:

1 hat model (diameter 4cm), 1 round non-woven fabric (3cm), 2 ribbons (width 0.6 long 9cm), 1 piece of lace (2.5cm wide and 20cm long), 1 small flower and 1 rhinestone, 1 satin-covered hairpin Steps:

1. First, stick the round non-woven fabric to the bottom of the hat to seal the hole.

2. The ribbons are criss-crossed and overlapped to form a "and" shape, and the middle points are overlapping and stitched into a bow, with small flowers and rhinestones attached in the middle.

3. The lace is shrunk, the head and tail are tightened and knotted to fix it, sewn into a wavy circle, and glued to the bottom of the hat.

4． Join another ribbon in a circle along the edge of the hat, finish with the bow from step 2 at the connection, and attach it to the hairpin.

TIPS: When gluing the lace at the bottom of the hat, you can leave about 0.5cm around the edge so that it doesn't stick to it. The layers of lace will be more beautiful. A must-learn for moms of baby girls! Super cute baby hair accessories DIY baby animal headband materials:

2 dot ribbons (width 3.8 long 21cm), 1 ribbon each (width 1 length 5cm, width 1 length 42cm), 1 piece each, cute 1 rag doll, 1 hair tie. Steps:

1. Place the dots of ribbon in the center and fold it in half, overlapping the center points and sewing them into a bow with needle and thread. Overlap and sew the two bows into a four-ear bow.

2. The satin ribbon is 1 width and 42 cm long. Divide it into 5 equal lengths using a "Z" shape. Wrinkle at the center point and sew with thread to form a windmill knot. Overlap it on the four-ear bow.

3. A ribbon 1 cm wide and 5 cm long should be wrapped around the center seam of the bow in step 2 to prevent the threads from being exposed. The excess length of the ribbon can be cut off.

4． Use hot melt glue to glue the cute rag doll to the bow in step 3, and then sew the bow to the hair band.

TIPS: When wrinkling the pinwheel knot, you can use long clips to fix the two sides to prevent the ribbon from sliding, making it easier to complete the step of wrinkling at the center point!