How does fttp take the route?

Question 1: How to route the optical fiber? (urgent) Hello, landlord.

Optical fiber is not allowed to bend hard, and it is fragile and easy to break. Not suitable for home or enterprise long-distance wiring.

It is suggested that the optical fiber be left at the entrance and the optical cat be placed at the entrance. Pull the network cable in.

Then pull the network cable into the house and install the route to achieve the same effect ~

Hope to adopt. Thank you.

Question 2: How to wire fttp indoor! If the wiring method of home decoration can meet the requirements of information-based home such as calling, surfing the Internet, video and entertainment anytime and anywhere, it is recommended to install dual-port information panels in the following positions.

The dual-port information panel recommends the installation location of the business support power socket.

There are at least two IPTV power outlets on the TV wall in the living room.

Living room sofa telephone

At least three power outlets were used for telephone and Internet access in the study.

Bedroom bedside table telephone, Internet access at least one power socket.

There are at least two IPTV power sockets in the bedroom TV wall.

There is at least one power socket at the door of the video monitoring room.

At least one power socket is located at the installation position of the optical fiber information panel.

1. From each information panel to the integrated information box, you need a Category 5 line (network line). Please don't choose ordinary telephone lines.

2. Each Category 5 cable is connected to the telephone port and Internet port of the information panel at the same time.

3. The five types of wires should be connected directly, not in series.

4, when decorating wiring, also should pay attention to the following points:

A, the network cable should not be wired at right angles as far as possible to avoid damage caused by five kinds of wires during pulling;

B, the distance between the network cable and the power cable should reach at least 15cm to avoid the interference of alternating current on data transmission;

C. When threading Category 5 cables, PVC pipes should be used for threading, and at least the length of cables in the information tray and information box should be reserved; More than 20cm;

D, after the five kinds of wires are worn, each network cable should be marked in the information box to identify the room where the information disk is located or its connection position, which is convenient for future use.

After you finish the indoor wiring construction, please be sure to carry out the acceptance test for each laid wire.

The test requires a pair of network cable testers (available in computer city or electronic products market, with a market price of 40- 100 yuan/pair). When testing, it is necessary to connect the main tester or remote tester at both ends of the tested network cable.

A. If the tested cable is normal, the numbers of the two test terminals will flash from 1 to 8 at the same time;

B, if the number sequence is wrong, it means that the wiring method is wrong or the cross wire is connected;

C, when there is a light is not bright, said the line is not connected;

D. if all the lights don't flash, it means that this line has more than 4 lines.

Note: Different brands of network cable tester have different meanings. Please pay attention to the instruction manual of the tester.

Question 3: How to wire the telecom fiber to the home? Whether you go to the corridor or home, the signal line from the telecom equipment to your home is the responsibility of the telecom staff. What you need to do is to lay network cables in each room and concentrate the other ends of all network cables in one place (it is best to reserve about 2 meters for each network cable. Remember it's best to pull the network cable through the pipe. This position is best near your door (indoors). If the optical fiber directly enters the home, then a fiber-optic cat (purchased by the head of the household from the telecom company) should be placed in the concentrated position of the network cable. The optical fiber cat is about 20 cm long and 15 cm high. It is necessary to lay two wires to connect a 2-hole panel and connect the power supply to the optical fiber cat adapter.

Question: how to take the wiring diagram of fttp? Don't take the wires. Just make a cabinet herding cats at the interface of fttp, and then connect it to the wireless router.

It doesn't take up space, and it can also be connected to the whole house.

My home is on the second floor, and the second route is used upstairs. Any house has an internet.

Question 5: fttp wiring problem 1 unplugging the optical fiber on the optical cat. It may be that the optical fiber plug was affected when moving the optical cable.

The optical fiber line can be moved. I changed the position of the light cat, unplugged the optical fiber plug and plugged it in again, and it will be fine.

If not, call the telecom staff. Their attitude is still relatively good.

It is best to use alternating current for optical fiber. If not, buy a larger cell phone battery, but make a battery holder and a DC plug.

Question 6: Specifications and requirements of optical fiber wiring in computer room How to wire in fttp and pay attention to the selection of optical fiber?

The choice of optical fiber should be based not only on the number of optical fiber cores and optical fiber types, but also on the use environment of optical cable. For example:

1, multimode fiber can be selected for transmission distance less than 2km, and relay or single-mode fiber can be selected for transmission distance greater than 2km.

2. When choosing optical fiber for building, we should pay attention to its flame retardancy, toxicity and smoke characteristics. Generally, flame retardant but smoky type can be selected in pipelines or forced ventilation places; If it is in an exposed environment, it should be flame retardant, non-toxic and smokeless.

3. When outdoor optical cables are directly buried, armored optical cables should be selected. When overhead, black plastic outer sheath and optical fiber with two or more reinforcing ribs can be selected. Optical fiber cable is used to complete.

Question: How to move the optical broadband in fttp community? A network cable connects a weak box in a room.

Question 8: How to connect Unicom fttp? Give three suggestions for your reference.

1. First go to the business hall and ask if fttp can be installed (if you don't have time to call). According to your description, it should be that the community in fttp needs to be rebuilt. Note: Not all cells can introduce optical fiber.

You don't have to worry about the transformation of fttp, the operators' workers will do it well.

3. Why don't you * * * share your optical fiber with other tenants? This will not only reduce your use cost (let them pay some money), but also get on well with them. A wireless router can solve it.

For reference only.

Question 9: How does fttp connect the wireless routing wiring in the new house? Just lay a network cable from 1 to 2. Just lay a network cable from 2 to other rooms. Or wire directly from 1 to Room 2 and the other four rooms, and put the router at 1. Each network port can be connected to a desktop or other wired equipment, and the radiation of the routing amplifier 1 is relatively small. At present, the general through-wall wiring is ideal, so it is not necessary to put it in the second position.

Question 10: Telecom fttp, how to arrange the wiring for home decoration?

You just need to lay the network cable of the multimedia box in every room. Telecom fttp needs a slim cat. Just connect the network cable to the slim cat and you can use it.