Aerial work responsibility agreement

5 Liability agreement for aerial work.

Aerial work usually refers to aerial work, which refers to the work carried out by people at a height based on a certain position. When working in a building, if working on a shelf more than 2m, it belongs to aerial work. I brought you a responsibility agreement about aerial work, I hope you like it!

Aerial work responsibility agreement 1 Party A: Shanghai Shangshi Property Management Co., Ltd.

Party B: Shanghai Donggang Construction Engineering Co., Ltd.

In order to do a good job in the safety management of the paint repair of the outdoor wall of Building 170 1, to prevent the occurrence of safety accidents and to ensure personal safety, Party A and Party B, on the basis of relevant national laws and regulations and relevant regulations of the company, signed this agreement on the principle of voluntariness and equality through full consultation.

I. Party A's responsibilities:

1. Before Party B enters the work site, Party A shall inform Party B's personnel of safety, provide Party B with safety operation procedures, conduct safety training for Party B's personnel, and inform Party B of the safety reward and punishment system.

2. Party A has the right to supervise, inspect and guide Party B during the construction period. For the problems found in the inspection, Party A will punish and reward Party B according to the relevant reward and punishment system of the company.

3. In case of personal injury during the operation, Party A has the obligation to assist Party B to handle the accident, prevent the accident from expanding, and assist relevant departments to investigate and collect evidence of the accident, but all expenses incurred during the period shall be borne by Party B. ..

Two. Party B's responsibilities

1. During the construction, Party B must set up a full-time security officer who is responsible for informing the operators of safety protection and training the safety operation procedures.

2. During the operation, Party B shall abide by the company's rules and regulations and take timely measures to eliminate "potential safety hazards" found during the operation.

3. Party B shall take full responsibility for the safety accidents during the operation. If losses are caused to the company, Party B shall compensate for the losses.

4. During the operation period, Party B is prohibited from drinking, fatigue and illegal operation, and Party A will conduct random inspection from time to time. If Party B is found to have violated the law during the sampling inspection, Party A will punish Party B according to the relevant regulations of the company.

5. According to the regulation of "one post and two responsibilities", Party B's project leader is also the person in charge of safety, responsible for the daily safety management of construction personnel and the safety of Party B's operators.

6. Before the operation starts, the project leader of Party B shall educate the operators on safety protection measures, and keep written stubs for future reference, and shall not arrange uneducated employees to enter the site.

7. Party B shall not enter the place outside the construction project area without authorization to touch and start the machinery, electrical appliances, control valves and other equipment, otherwise Party B shall bear all the responsibilities for the accidents caused thereby.

8. The tools used by Party B shall be responsible for their safety protection measures and bear the safety responsibility. If the safety lifting rope, safety lifting plate and safety belt are found to be damaged, they must be replaced, and Party B shall bear all the responsibilities for the accidents caused thereby.

Three. Party A and Party B shall strictly abide by the terms of this agreement, perform their respective duties and do civilized work.

Four. This agreement shall come into force from the date of signing to the end of the project in duplicate, with each party holding one copy.

Verb (abbreviation of verb) Matters not covered in this contract shall be settled by both parties on the principle of friendly negotiation.

Party A: Shanghai Secco Property Management Co., Ltd. Party B: Shanghai Donggang Construction Engineering Co., Ltd.

Person in charge: person in charge:

Date of signing: Date of signing:

Aerial work responsibility agreement Part 2

Party A:

Party B:

Scope of construction: Area C maintenance and external wall thermal insulation coating project of the first phase of farmers' directional resettlement house in Dongbaju Ovary.

I. Party A's responsibilities:

1. Party A is responsible for issuing the construction task list to Party B and cooperating with Party B to create the construction conditions.

2. Party A's Engineering Department and Property Management and Safety Department are responsible for checking the civilized construction of this project. Fire fighting, safety, etc. , stop all kinds of illegal phenomena on the construction site in time, and deal with Party B and the parties according to relevant regulations and the seriousness of the case. (According to relevant regulations of community management)

3. Party A, property management and the owner are responsible for the acceptance after rectification.

Two. Party B's responsibilities:

1, all workers entering the community must abide by the rules and regulations of the community; All workers must bring a copy of their ID cards and registration photos to the Project Department for registration.

2. It is forbidden for anyone to pick up and ride the power cord in the community;

3, non-working personnel are not allowed to enter the construction area, homework personnel without permission, it is forbidden to engage in this type of work;

4. It is forbidden to wear leather shoes and shoes with nails for aerial work;

5. During the construction period, Party B shall not arbitrarily expand the construction area, block the traffic and the safe evacuation passage of the building, and shall not pile up all kinds of building materials and equipment.

6. All kinds of wastes and articles left over from construction should be cleaned up on the day of construction to ensure the cleanliness of the site and residential buildings.

7. Without the permission of the person in charge of the property management office, the residential safety protection facilities and safety signs shall not be removed at will;

8, it is forbidden to throw things down at high altitude, aerial work must fasten your seat belt.

9. In the process of construction, Party B shall put an end to uncivilized phenomena such as shirtless and barefoot, and the construction personnel shall have good personal hygiene and shall not be unkempt.

10. If Party B violates the above terms and conditions, causing losses and accidents to the announcement facilities and the owner's room in the community, Party B shall be responsible for compensation according to the price. If the circumstances are serious, Party A has the right to order it to stop work for rectification, and relevant personnel will be investigated for criminal responsibility.

1 1. During the construction, Party B shall always pay attention to safety, and Party B shall be responsible for all major and minor accidents during the construction, and Party A shall not be responsible.

12. Party B must make it clear that the person in charge of construction is the first person in charge of safety, the person in charge of on-site construction is the first person in charge of on-site safety, and the first person in charge of Party B's safety is fully responsible for the construction personnel and on-site safety.

13. Party B shall take full responsibility for all safety accidents caused by illegal operation in the construction process.

14. Party B must have relevant construction qualifications recognized by the state, and the construction personnel must have "personal accident insurance".

15. Construction personnel must strictly abide by the Safety Regulations for Aerial Work during construction. If they still disobey the management personnel after education, Party A has the right to punish them. If the circumstances are serious, Party A has the right to clear them out of the mall.

16. When Party B's construction personnel enter the site at night, they should apply to the floor for night decoration, enter the site with a pass, and enter and exit from the entrance designated by the mall. Security guards have the right to manage the personnel who enter and leave the site for night decoration.

17. Smoking is strictly prohibited on the construction site. Found cigarette butts 100 yuan/piece, found smoking on the spot, fined 1000 yuan.

18, open flame is strictly prohibited in the construction site. If it is really necessary to use naked flame, you must go through the hot formalities in the fire control room of the safety management department of the mall. The approved hot work site must be supervised by special personnel, and equipped with water and fire extinguishing equipment before construction; Otherwise, all losses caused shall be borne by Party B, and those with serious circumstances shall be investigated for legal responsibility.

19. The use of various electrical appliances, lines and lighting power sources in residential areas must be reported to the electrician of the project department for examination and approval, and construction can only be started after approval. During the construction, it is forbidden to accumulate water on the ground to prevent underwater leakage, otherwise Party B will be responsible for the consequences.

20. During construction, the bearing columns, beams and other public facilities of the original structure shall not be damaged. It is forbidden to use and damage all kinds of fire control facilities in the building. Unauthorized use, depending on the circumstances, will be fined 1000- 10000 yuan. If public facilities such as fire fighting facilities are damaged, compensation shall be paid according to the price, and the alarm and spraying functions will not work, resulting in an accident. Party B:

2 1. Construction personnel are not allowed to walk around in a thick building without a construction business site. Anyone who damages the facilities and user's articles in the building shall be compensated at twice the selling price. Once found in other business premises at night, Party A has the right to clean up and stop Party B's construction, and impose a fine above 500 yuan.

22. This Agreement is made in duplicate, with each party holding one copy.

Duration: year month day to year month day.

Signature and seal of the person in charge of Party A:

Signature and seal of the person in charge of Party B:

Date:

Date:

Chapter 3 of aerial work responsibility agreement

Party A:

Party B:

1. Party A of Shen 'an Group (hereinafter referred to as Party B) entrusts Party B to provide night lighting maintenance services for the first building. In order to ensure the safety of personnel, equipment and equipment during maintenance, Party A and Party B voluntarily sign this agreement in accordance with the National Security Law of People's Republic of China (PRC), Labor Law of People's Republic of China (PRC) and other laws, regulations and provisions.

Two. Validity of this agreement: the safety responsibilities of both parties during the whole maintenance process.

1. Both parties must conscientiously implement the guidelines, policies, rules and regulations on safety production promulgated by People's Republic of China (PRC) and the national and local safety production authorities, and strictly implement the labor protection, rules and regulations, and the aerial work management system and other systems and regulations.

2. During the operation, Party B shall designate a special person to be responsible for the safety supervision and management of aerial work; Party A shall assist in supervision and inspection.

3. During the contract period, Party A and Party B must earnestly perform their respective safety responsibilities to ensure safe operation.

Three. Party A's security responsibilities.

1. Party A requires Party B to review the qualifications of aerial workers to confirm that they meet and satisfy the following conditions:

(1) Holding the business license and qualification certificate issued by relevant departments; Hold the identity certificate and power of attorney of the legal representative.

(2) The configuration and certificates of relevant responsible persons and aerial workers meet the requirements of safe operation.

(3) Equipped with machinery, instruments, safety protection facilities and safety appliances that meet the needs of safe operation.

(4) The safety management system is complete. Including aerial work management system, safety inspection system and safety education system (attached)

2. Inspect Party B's job site from time to time, and stop and correct the behaviors of Party B's personnel that violate relevant safety production rules and regulations in production; For serious violations, immediately order them to stop working.

3. Party A is responsible for ground construction and patrol inspection.

Four. Safety responsibilities that Party B shall bear:

1. The operating procedures formulated by Party B must be approved by Party A before the construction preparation yesterday.

2. During field operation, the aerial work management system must be strictly implemented, and Party A's permission must be obtained before work.

3. Before work, check the construction machinery, instruments and safety protection facilities to ensure compliance with safety regulations.

4. Party B's operating personnel shall carefully check their work area, environment, operating facilities, equipment and tools, and stop their operations immediately if they find hidden dangers, and then continue their operations after rectification and implementation.

5. All kinds of equipment and tools used in the work should meet the work requirements. Before construction every day, the scaffolding on the construction site will be inspected by special personnel, and the hidden dangers will be rectified in time. Party B shall not dismantle or change various safety protection facilities, obstacles, safety signs, warning signs and grounding wires without authorization.

6. Employment shall comply with the Labor Law of People's Republic of China (PRC) and other laws, regulations and rules, and it is forbidden to use underage workers and personnel with occupational taboos for construction work.

7. Party B shall earnestly implement the installation and use of safety equipment and safety supplies on the construction site to ensure the construction safety.

8. The person in charge of Party B (the first person in charge of safety construction) must promptly rectify the hidden dangers and problems raised in Party A's safety inspection.

9. Party B shall accept the safety supervision, management and guidance of Party A. During the construction process, Party B's personnel shall promptly notify Party A of the unsafe conditions. Party B has the right to refuse Party A's illegal command and force risky operation.

10. If all accidents or losses are caused to a third party due to improper safety measures taken by Party B, violation of relevant safety rules and regulations and safety matters listed in this agreement, Party B shall bear the economic losses and legal responsibilities caused thereby.

5. This agreement is made in duplicate, which shall come into effect after being signed and sealed by both parties, and have the same legal effect.

Other unfinished matters of intransitive verbs shall be settled by both parties through consultation.

Party A (seal) and Party B (seal)

Representative (signature) Representative (signature)

Address: office address:

Tel: Tel:

Fax: Fax:

Postal code:

Chapter 4 of aerial work responsibility agreement

Engineering project:

Party A:

Party B:

Through full friendly consultation between both parties, based on the principles of equality, mutual benefit, fairness and justice, in order to clarify the responsibilities, rights and interests of both parties and ensure the safe and timely completion of the service project, this contract is hereby signed as follows:

1. Party A designates Party B as the contractor, and the construction period is from to. Under special circumstances (in case of force majeure, such as storm and lightning, etc.). ), the construction period will be postponed.

Second, the construction site:

Three. Rights and obligations of both parties:

1. Responsibilities and obligations of Party A

Before entering the site for high-altitude construction, make on-site oral safety disclosure to the person in charge of Party B, including: safety rules and regulations of the project and safety precautions related to the project.

In order to prevent false boarding, Party A shall set up warning signs at appropriate positions in the forbidden area or unstable structure area.

Party A has the responsibility and obligation to supervise and inspect Party B's construction equipment and construction process.

2. Party B's safety measures and responsibilities

The person in charge of Party B is the person in charge of production safety, who is responsible for the daily safety management of the project, strictly abides by the rules and regulations of production safety, and appoints a special person to supervise the safety construction operation.

Before construction, the safety education of safety precautions and measures disclosure must be carried out for subordinates, and the personnel without safety education shall not be arranged to enter the workplace.

Education and supervision personnel are not allowed to enter places outside the construction project area, and are not allowed to touch and start machinery, electrical appliances, control valves and other equipment at will, otherwise Party B will bear all the responsibilities for the accidents caused thereby.

Any work carried out at a height of 2 meters or more shall be regarded as aerial work.

Workers working at height must be in good health. Persons suffering from mental illness, epilepsy, hypertension, heart disease and other diseases that are not suitable for working at heights shall not participate in working at heights. When employees are found to be drinking or depressed, it is forbidden to work at heights.

Safety belts must be used when working with suspension ropes. Check the seat belt before use, and the test load is 225 kg. After the test, check whether there is deformation or rupture, and make test records. Unqualified seat belts should be handled in time.

The hook or rope of the seat belt should be hung on a solid part or a wire rope specially designed for hanging the seat belt. Don't hang on moving or unstable objects.

Tool bags should be used for aerial work. Larger tools should be tied to solid components with ropes, and cannot be placed casually to prevent accidents from falling from high altitude.

When working high above the ground, no one is allowed to walk or stay under the workplace except the relevant personnel. The workplace should be fenced or equipped with other protective devices to prevent falling objects from injuring people. If working on the grid platform, in order to prevent tools and equipment from falling, wooden boards should be laid.

Tools and materials are not allowed to be thrown up and down, but should be hung down or up after the rope is tied, so as not to hurt the people below or damage the scaffold.

When the upper and lower floors are working at the same time, a tight and firm protective partition, shed or other isolation facilities must be erected in the middle, and the staff must wear safety helmets.

When working in the open air at the altitude below zero in winter, if necessary, there should be a heating and rest place near the construction area, and the heating equipment should be managed by special personnel, paying attention to fire prevention.

In strong winds of magnitude 6 and above, as well as severe weather such as rainstorm, lightning and fog, open-air high-altitude operations should be stopped.

The use of Party A or the machinery, electrical appliances and other facilities related to Party A must be approved by Party A, and Party A shall be responsible for its safety protection measures and assume safety responsibilities.

Party B shall be responsible for the safe construction of the project and the safety of all personnel involved in the project.

Party B shall be responsible for all safety responsibilities of the project construction. If a production safety accident occurs during the construction, Party B shall bear all accident and economic responsibilities.

Four. Party A and Party B shall strictly abide by the terms of this contract, perform their respective duties and do a good job in civilized construction.

5. This contract is made in duplicate, each party holds one copy, both of which have legal effect. This contract shall come into force as of the date of signing. Matters not covered herein shall be settled by both parties through friendly negotiation.

Party A (signature of representative):

Party B (signature of representative):

Party A (Contract Seal):

Party B (Contract Seal):

Chapter 5 of aerial work responsibility agreement

Party A:

Party B:

I. Introduction

1, the construction party shall seriously implement the national, provincial and municipal safety regulations, standards and specifications related to aerial work;

2. Seriously organize the implementation of safety technical measures to ensure the reasonable investment of safety funds for aerial work;

3. Organize regular safety inspections to eliminate hidden dangers of accidents and stop illegal operations and behaviors;

4. Be responsible for the safety education and safety technical training for employees entering aerial work;

5. Be responsible for organizing the inspection of aerial work safety equipment and temporary aerial work safety used in the construction site, and use them only after they are qualified;

6, responsible for the establishment of aerial work safety post responsibility system, organize inspection and assessment of the actual situation; Do not use unlicensed personnel to work at their posts;

7, do not use fake and shoddy protection facilities and supplies;

8, aerial work safety accidents should be reported immediately, protect the scene, to participate in the accident investigation; Formulate safety measures for aerial work and organize their implementation.

Second, the object safety

1, materials used for aerial work should be piled up smoothly, and shall not interfere with safe passage. You can't throw objects when passing them.

2. Operation of aisles, access plates and climbing equipment. , should be cleaned at any time.

3. Dismantled objects, surplus materials and wastes shall be cleared away in time, and shall not be arbitrarily placed or discarded downwards.

4, the construction workplace, any material that may fall, should be removed first, in case of falling cuts.

Third, facility safety.

1, the climbing frame and climbing facilities used for site construction shall be determined in the construction organization design. On-site climbing should use climbing facilities on building structures or scaffolding, and manned vertical transportation equipment can also be used. You can use ladders or other climbing facilities when climbing.

2, climbing equipment structure must be solid and reliable. The service load of the pedals for people to get up and down should not be greater than1100 n. If there are special operations on the ladder surface, the load should be checked according to the actual situation.

3, mobile ladder, should according to the current national standards for its quality acceptance. The bottom of the ladder foot should be solid and not allowed to be used. The upper end of the ladder should be fixed. The working angle of the vertical ladder should be 75 5, the pedal spacing should be 30cm, and there should be no gap. If the use of the ladder needs to be extended, reliable connection measures must be taken, and the joint shall not exceed 1. The strength of the connected ladder beam should not be lower than that of a single ladder beam. When using the folding ladder, the upper included angle should be 35 ~ 45, the hinge must be firm, and reliable support measures should be taken. The fixed straight ladder shall be made of metal material. The width of the ladder should not be greater than 50cm, the support should be angle steel not less than ∟70×6, and the embedding and welding must be firm. The pedal at the top of the ladder should be flush with the climbing top surface, and the handrail with the height of 1~ 1.5m should be added.

4. When climbing with a straight ladder, the suitable climbing height is 5m. More than 2m, should add protective cage; When the height exceeds 8m, a ladder platform must be set.

Fourth, aerial work.

1. Any work carried out at a height of 2 meters or more shall be regarded as aerial work. All work that can be completed on the ground in advance must be completed on the ground to minimize aerial work.

2. Personnel who work at heights must be in good health. Those who suffer from mental illness, epilepsy and have been identified by doctors as having high blood pressure and heart disease should not work at heights, and are not allowed to participate in high-altitude operations. When employees are found to be drinking or depressed, it is forbidden to work at heights. Scaffolding must be erected or measures must be taken to prevent the team from falling when working at heights.

3. When working on dangerous edges such as dam crest, steep slope, roof, cliff, tower, suspension bridge, etc., a safety net or protective railing should be installed at the airport side, otherwise the staff must use safety belts. Ice, snow, gravel and soil on cliffs, steep slopes or sidewalks should be cleaned frequently, and railings with a height of 1 m should be set outside. Set 18 cm high side plate or soil ridge on the inner side of the railing to prevent falling objects from hurting people.

4. When working on scaffolding without scaffolding or railings and the height exceeds 1.5m, you must use safety belts or take other reliable safety measures. Check the seat belt before use, and the test load is 225 kg. After the test, check whether there is deformation or rupture, and make test records. Unqualified seat belts should be handled in time.

5. The hook or rope of the safety belt should be hung on a solid part or a wire rope specially designed for hanging the safety belt. Don't hang on moving or unstable objects.

6. Tool bags should be used for high-altitude operations. Larger tools should be tied to solid components with ropes, and cannot be placed casually to prevent accidents from falling from high altitude.

7. When working high above the ground, no one is allowed to walk or stay under the workplace except the relevant personnel. Fences or other protective devices should be installed under the workplace to prevent falling objects from injuring people. If working on the grid platform, in order to prevent tools and equipment from falling, wooden boards should be laid.

8. Tools and materials are not allowed to be thrown up and down. After being tied with rope, it should be hung down or hung up, so as not to hurt the staff below or damage the scaffold.

9. When the upper and lower floors are working at the same time, a tight and firm protective partition, tent or other isolation facilities must be set up in the middle, and the staff must wear safety helmets.

10, open-air operation at high altitude below zero 10 degree in winter. When necessary, there should be a heating and rest place near the construction area, and the heating equipment should be managed by special personnel, paying attention to fire prevention.

1 1, strong winds of magnitude 6 or above, and severe weather such as rainstorm, lightning and fog, outdoor operations should be stopped.

12. It is forbidden to work on unstable structures (such as asbestos tile roofs). In order to prevent boarding by mistake, warning signs should be hung at the necessary positions of the building.

Five, electricity safety

1, contact the relevant unit to cut off the power supply before working near the power line. Work can only be started after power failure is confirmed, and an insulating retaining wall is set in the work area. It is forbidden to work under high voltage lines.

2. The metal shell and running track of all mechanical and electrical equipment must have reliable grounding or repeated grounding safety measures.

3. Non-electrical personnel are not allowed to decorate electrical equipment and lines. When using hand-held electric tools, they must be insulated reliably, with good grounding or zero connection measures, and insulating gloves should be worn when operating.

Intransitive verb others

1. When defects or hidden dangers are found in the safety facilities for aerial work during construction, they must be solved immediately.

2, to endanger personal safety, should immediately stop operation, rectification. No one is allowed to move or remove all safety protection facilities and safety signs without authorization.

3, some really need to be removed or moved because of the construction, must be reported to the construction director for approval before dismantling, and be restored after the completion of the work. The above agreement shall come into effect from the date of signing and remain valid for a long time. Party A has nothing to do with safety accidents and personal injuries caused by the construction unit's violation of this agreement or other factors other than this agreement. If the construction unit causes property losses to Party A due to improper operation during the construction process, it shall unconditionally compensate.

Party A (official seal): _ _ _ _ _ _

Legal representative (signature): _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Party B (official seal): _ _ _ _ _ _

Legal representative (signature): _ _ _ _ _ _

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _