How to install the suction door

Question 1: How to install the door suction for the security door? If your security door is a wooden door, you can install it according to the normal door suction method.

If your security door is an iron gate, it is recommended to pretend to suck it well.

Question 2: How to install the door suction in the room Although the door suction is a small thing, it can't be installed casually, because it is still a moving part after all, and it has to bear the impact and pull of the wooden door and the stress of the wall and floor tiles that fix it. In addition, the impact on the door should also be considered. Therefore, the installation quality of door suction is directly related to the safety of doors, walls, floors, tiles and people. Door suction in ordinary families is generally divided into wall-mounted and floor-mounted, and the choice of two kinds of door suction should be determined according to the specific installation location and installation conditions. Generally, the fixed wall is installed first, and then the movable end (the part on the door panel) is installed.

Floor suction door: the fixed end is fixed at two points, and two holes should be punched in the floor material (electric drill for floor, impact drill for cement or tile floor), and then fixed with nylon expansion plug U and screws; When installing the movable end on the door, it should be positioned according to the cooperation of the fixed end.

Wall-mounted suction door: the fixed end is usually fixed at three points, and three holes are punched in the wall (try to use an impact drill, and if it is a concrete load-bearing wall, use an electric hammer, but be sure to prevent the center position of the hole from deviating too much), and then fix it with nylon expansion plugs and screws; When installing the movable end on the door, it should also be positioned according to the cooperation of the fixed end.

The movable end of the door can be installed with an ordinary electric drill.

It is particularly important to note that many wall-mounted door suction devices are also dual-purpose door suction devices, but from a mechanical point of view, as long as the wall is allowed to be installed, the ground installation method must be avoided. Because the wall-to-ground dual-purpose suction door cannot be guaranteed to be reliable if it is installed on the ground.

Question 3: How to install the aluminum alloy door? The long end of the door suction door is installed on the wall, and the short end is installed at the appropriate position in the lower corner of the door leaf. Generally speaking, screws are drilled or drilled with a 3.0 mm drill. For good suction, it is best to install the door and one end, and print the position with a pen at the other end. Watch the glass.

Question 4: How to remove the suction head of the door suction, that is, the part installed on the door? There are two small holes where the door is installed. Put your two nails in, then hold the nail with your other hand and twist it. Screw it in like a screw.

Question 5: How to install the door suction? There are two ways to install the door suction, one is to install it on the ground, and the other is to install it on the wall or skirting board. At present, the function of door suction is mostly based on the principle of magnetic force. Now take a magnetic door suction installed on the floor as an example. The types and specifications of the door suction are determined according to the distance between the door panel and the collision wall and objects, and the metal is the best. Installed on skirting board or wall, the lower the better. No matter where it is installed, the first principle should be that door locks and doors should not collide with walls or other objects! 1. Determine the installation method of door suction. Is the door suction installed on the wall or on the floor? It depends on the actual situation. 2. To test the suction function of the door, please open the door to the maximum position and check whether the distance between the door suction inlet and the door is appropriate. After the door suction position is roughly determined, open the door and test it to see if it is suitable. If it is not suitable, fine-tune it up, down, left and right until it is at the right position and angle. 3. After determining the position of the door suction, if it is on the ground, it needs to be limited to the stop position, and then confirm the position of the opposite door and mark it. Draw a line to ensure that the child drives to the maximum position. Finally, determine the installation position of the door suction. 4. Draw the positioning position of the door suction. According to the above test, it is best to position the door suction twice, mainly for convenience of installation. In order to better confirm the angle of door suction and door opening, 5, and then ask the master to drill. Now the installation hole of the door suction is drilled in the ground. 6. Assembly of fixed end of door suction port. Install the fixed end of the door suction inlet and tighten the screws. 7. Fix the door suction on the ground and tighten the screw with a small inner corner. This is a delicate job. After going through the procedures of position confirmation, drilling and assembly, the next work is to install the fixed end on the ground. Tighten the screw at the fixed end with the included internal corner tool, and the door suction will be installed automatically. 8. Determine the door suction position on the door. Just tighten the door suction end on the door. After the door suction ends are installed, it should be almost the same. The most important thing is to test, open the door until you are drunk, then find the suction position on the door and tighten the suction end with screws. 9. Fine-tune the angle of the fixed end of the door suction port, and then tighten it completely. The last step of door suction installation is fine-tuning, rotating the angle of door suction to make it match the door suction at the door end, and finally tightening the screws completely.

Question 6: How to install the door suction 1 on the wall: first drill a hole in the wall with an electric drill and nail a wooden wedge in the hole.

2. Install the door suction base on the wooden wedge with self-tapping screws.

3: Install the other half of the door suction behind the door with self-tapping screws.

Question 7: What is the structure inside the door suction? How was it installed? 100 door suction has two installation methods, one is ground installation, and the other is wall or skirting board installation. At present, the function of door suction is mostly based on the principle of magnetic force. Now take a magnetic door suction installed on the floor as an example. The types and specifications of the door suction are determined according to the distance between the door panel and the collision wall and objects, and the metal is the best. Installed on skirting board or wall, the lower the better. No matter where it is installed, the first principle should be that door locks and doors should not collide with walls or other objects!

1. Determine the installation method of the door suction.

Whether the door suction is installed on the wall or the floor. It depends on the actual situation.

2. Test the suction effect of the door

To open the door to the maximum position, please check whether the suction force of the door and the distance between the doors are appropriate. After the position of the door suction is roughly determined, open the door to test whether it is suitable. If it is not suitable, fine-tune it up and down from left to right until it is at the right position and angle.

3. After determining the position of the door suction, if it is located on the ground, it needs to be limited to the stop position, and then confirm the position of the opposite door and mark it. Draw a line to ensure that the child drives to the maximum position. Finally, determine the installation position of the door suction.

4. Draw the door suction positioning position.

According to the above tests, it is best to locate the door suction twice, mainly for convenience of installation. In order to better confirm the angle of door suction and door opening.

5, and then ask the master to drill. Now the installation hole of the door suction is drilled in the ground.

6. Assembly of fixed end of door suction

Install the fixed end of the door suction inlet and tighten the screws.

7, the ground fixed door suction

Screwing a screw with a small inner corner is a delicate job. After confirming the position, punching, assembling and other procedures, the next work is to install the fixed end on the ground, tighten the screw of the fixed end with the attached internal corner tool, and the door suction will be automatically installed.

8. Determine the door suction position on the door.

Just tighten the door suction end on the door. After the door suction ends are installed, it should be almost the same. The most important thing is to test, open the door until you are drunk, then find the suction position on the door and tighten the suction end with screws.

9. Fine tuning

Fine-tune the angle of the fixed end of the door suction port, and then tighten it completely. The last step of door suction installation is fine-tuning, rotating the angle of door suction to make it match the door suction at the door end, and finally tightening the screws completely.

Question 8: Who knows the difference between door bumping and door suction? Knocking the door is to limit the angle and direction of opening the door and prevent you from touching other things when the angle is too large.

Or you locate the direction of the door, for example, you only allow the door to open outwards (you can install a door bump on the ground inside the door)

Door suction is to prevent the door from closing itself (for example, when there is wind, the door will close itself), and also to avoid damaging the door lock by opening the door too hard.

Question 9: Who has been decorated? Tell me how to install the door suction of balcony door with 1 Check with the owner first whether the door suction is installed on the ground or on the wall. Because this is Wei ...

2. Step 2: Open the door to the required maximum position and test whether the door suction function is reasonable and whether the distance between the door suction and the door is ...

3. After the final location is determined, locate it on the floor tile. First, confirm the stop position of the door on the floor tile with a pencil.

Question 10: Is it better to install the door suction on the skirting board or the wall, above or below the door? The lower the better. No matter where it is installed, the first principle should be that door locks and doors should not collide with walls or other objects!