Job Recruitment Website - Zhaopincom - How to install a suit door?
How to install a suit door?
Installation process of indoor suit door:
1. Cleaning the site: after arriving at the construction site, clean the door opening and installation site, measure the size of the door opening, plan the installation method in mind, and measure the size of the door leaf. It is forbidden to damage and dirty the wall and ground during construction.
2. Combined door frame: the top plate of the door is generally 20-50mm longer than the actual size of the door opening, and the gap for installing the door is 6-8 mm. Nail two nails on one side with the top plate of the door according to the actual size of the door leaf to fix the door frame, and level the upper and lower corners of the door opening with hand-pulled adhesive tape. Nail four pull tabs on the left and right sides of the door frame, put the door frame in the doorway, and nail two pull tabs in the middle of the top plate.
3. Install the door frame: put the door frame in the center of the door opening, divide the two sides equally, and fix the gap between the door frame and the door opening on both sides with sawdust. The height from the floor to the door leaf is 10 mm. First, install the hinge with the vertical door frame, and then fix the door frame.
4. Install the door leaf: install hinges on the door leaf, pay attention to the flatness of the door leaf and the door frame (keep the line position), install the door leaf on the fixed door frame, close the door, see if it can be opened and closed freely, whether the top plate of the door is suitable, whether the other side plate is closed up and down, pad the door frame with sawdust, and try to see if the door leaf can be closed freely.
5. Line installation: Cut the line into 45 degrees according to the size of the door frame, paste the vertical long line and the horizontal short line into a 90-degree angle with 502 glue, then nail it on the door frame and cover it with nail strips.
6. Install the lock head: firstly, cover the outer handle cover at the lock hole position of the door leaf, take two screw vacancies, and install the two vacancies with a 10mm twist drill; Install the lock core into the door leaf from the side, install the lock core fixing screws, then cover the outer handle, insert the handle pin from the inside, cover the inner cover, install two lock fixing screws, and debug whether the handle and safety can be used normally; Close the door, determine the installation position of the lock cover, chisel the lock cover opening by hand, put the lock bottom cover and face cover into the cover opening, and install the fixing screws after debugging.
7. Installation of door suction: above the bottom of the door 100mm can be installed and fixed at will. Pay attention to the installation method of wall bottom suction: a, concrete wall is suitable for installation with expanded rubber particles; B, brick wall is suitable for cork installation.
8. Cleaning inspection: check whether the surfaces of door frames and doors are damaged, and patch up the mounting line interface and locking interface with gypsum or paint the damaged surfaces with colored crayons; Try the lock handle and safety again to see if it can be used normally; Ask the customer whether the door leaf protective film is uncovered; Wash the walls, doors, doorframes and lines with towels, clean the ground and take away the garbage.
The above is how to install the suit door brought by Bian Xiao. The whole content of the installation process of indoor suit door.
- Related articles
- Whether the rubber mixer in the rubber factory belongs to a special type of work, please ask professionals to answer, preferably lawyers, thank you.
- Can Laos Sun Paper still go?
- Does China Communications Road and Bridge South China Engineering Co., Ltd. have an establishment?
- What are the five most classic Hakka dishes in Meizhou, Guangdong?
- What will happen if the boss submits his resignation letter on his behalf? Will it be serious?
- Is Weilai Taoyue a Fortune 500 company?
- What can ordinary people do except go to work in a factory?
- How to get to wanda plaza in Jiangbei from Jinfeng intersection of Guanzhong Road in Ningbo?
- What are the volunteers for the Asian Games?
- How about the Postal Savings Bank of China Co., Ltd. Nanchong Branch?